On my Alix box, the mouse pointer got unusably slow in X after upgrading
to OpenBSD 5.1. I am using an old Logitech PS/2 three button mouse.
I used to be able to adjust the mouse speed using xset(1) in OpenBSD 5.0,
but this does not appear to work anymore.
X is started with no configuration file. I have noticed several mouse
related problems on the mailing list. However, those were related to
the synaptics driver which I do not think X is using in my case.
Is there an easy solution to this problem?
dmesg & Xorg.0.log below
OpenBSD 5.1 (GENERIC) #160: Sun Feb 12 09:46:33 MST 2012
[email protected]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 499
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
real mem = 259252224 (247MB)
avail mem = 244920320 (233MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 01/16/09, BIOS32 rev. 0 @ 0xfa960
apm0 at bios0: Power Management spec V1.2 (slowidle)
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdfb4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf40/112 (5 entries)
pcibios0: bad IRQ table checksum
pcibios0: PCI BIOS has 5 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0xa800 0xef000/0x1000!
cpu0 at mainbus0: (uniprocessor)
amdmsr0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
vga1 at pci0 dev 1 function 1 "AMD Geode LX Video" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 13 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:0d:b9:0d:5a:5c
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <TRANSCEND>
wd0: 1-sector PIO, LBA, 7647MB, 15662304 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
auglx0 at pci0 dev 15 function 3 "AMD CS5536 Audio" rev 0x01: irq 11, CS5536
AC97
ac97: codec id 0x414c4770 (Avance Logic ALC203 rev 0)
ac97: codec features headphone, 20 bit DAC, 18 bit ADC, No 3D Stereo
audio0 at auglx0
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 5, version 1.0,
legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 5
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
wbsio0 at isa0 port 0x2e/2: W83627HF rev 0x41
lm1 at wbsio0 port 0x290/8: W83627HF
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
mtrr: K6-family MTRR support (2 registers)
umass0 at uhub0 port 4 configuration 1 interface 0 "Western Digital External
HDD" rev 2.00/1.75 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <WD, 3200BEV External, 1.75> SCSI2 0/direct fixed
serial.10580704394D31303132
sd0: 305245MB, 512 bytes/sector, 625142448 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
umidi0 at uhub1 port 3 configuration 1 interface 0 "KORG INC. nanoKONTROL" rev
1.10/1.00 addr 2
umidi0: (genuine USB-MIDI)
umidi0: out=1, in=1
midi0 at umidi0: <USB MIDI I/F>
root on wd0a (0e3b4dcb5303113c.a) swap on wd0b dump on wd0b
[2754154.311] (--) checkDevMem: using aperture driver /dev/xf86
[2754154.356] (--) Using wscons driver on /dev/ttyC4 in pcvt compatibility mode
(version 3.32)
[2754154.380]
X.Org X Server 1.11.4
Release Date: 2012-01-27
[2754154.380] X Protocol Version 11, Revision 0
[2754154.381] Build Operating System: OpenBSD 5.1 i386
[2754154.381] Current Operating System: OpenBSD box.my.domain 5.1 GENERIC#160
i386
[2754154.382] Build Date: 11 February 2012 10:00:22PM
[2754154.382]
[2754154.382] Current version of pixman: 0.22.2
[2754154.382] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[2754154.382] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[2754154.383] (==) Log file: "/var/log/Xorg.0.log", Time: Thu May 31 20:29:43
2012
[2754154.392] (==) Using system config directory
"/usr/X11R6/share/X11/xorg.conf.d"
[2754154.400] (==) No Layout section. Using the first Screen section.
[2754154.401] (==) No screen section available. Using defaults.
[2754154.401] (**) |-->Screen "Default Screen Section" (0)
[2754154.401] (**) | |-->Monitor "<default monitor>"
[2754154.404] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[2754154.404] (==) Disabling SIGIO handlers for input devices
[2754154.404] (==) Automatically adding devices
[2754154.405] (==) Automatically enabling devices
[2754154.434] (==) FontPath set to:
/usr/X11R6/lib/X11/fonts/misc/,
/usr/X11R6/lib/X11/fonts/TTF/,
/usr/X11R6/lib/X11/fonts/OTF/,
/usr/X11R6/lib/X11/fonts/Type1/,
/usr/X11R6/lib/X11/fonts/100dpi/,
/usr/X11R6/lib/X11/fonts/75dpi/
[2754154.434] (==) ModulePath set to "/usr/X11R6/lib/modules"
[2754154.434] (II) The server relies on wscons to provide the list of input
devices.
If no devices become available, reconfigure wscons or disable
AutoAddDevices.
[2754154.435] (II) Loader magic: 0x3c020020
[2754154.435] (II) Module ABI versions:
[2754154.435] X.Org ANSI C Emulation: 0.4
[2754154.435] X.Org Video Driver: 11.0
[2754154.435] X.Org XInput driver : 13.0
[2754154.435] X.Org Server Extension : 6.0
[2754154.438] (--) PCI:*(0:0:1:1) 1022:2081:1022:2081 rev 0, Mem @
0xee000000/16777216, 0xefff0000/16384, 0xeffec000/16384, 0xeffe8000/16384,
0xefff8000/16384
[2754154.438] (II) LoadModule: "extmod"
[2754154.449] (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.so
[2754154.454] (II) Module extmod: vendor="X.Org Foundation"
[2754154.454] compiled for 1.11.4, module version = 1.0.0
[2754154.454] Module class: X.Org Server Extension
[2754154.454] ABI class: X.Org Server Extension, version 6.0
[2754154.454] (II) Loading extension MIT-SCREEN-SAVER
[2754154.454] (II) Loading extension XFree86-VidModeExtension
[2754154.454] (II) Loading extension XFree86-DGA
[2754154.455] (II) Loading extension DPMS
[2754154.455] (II) Loading extension XVideo
[2754154.456] (II) Loading extension XVideo-MotionCompensation
[2754154.456] (II) Loading extension X-Resource
[2754154.456] (II) LoadModule: "dbe"
[2754154.461] (II) Loading /usr/X11R6/lib/modules/extensions/libdbe.so
[2754154.465] (II) Module dbe: vendor="X.Org Foundation"
[2754154.465] compiled for 1.11.4, module version = 1.0.0
[2754154.465] Module class: X.Org Server Extension
[2754154.465] ABI class: X.Org Server Extension, version 6.0
[2754154.465] (II) Loading extension DOUBLE-BUFFER
[2754154.465] (II) LoadModule: "glx"
[2754154.471] (II) Loading /usr/X11R6/lib/modules/extensions/libglx.so
[2754154.478] (II) Module glx: vendor="X.Org Foundation"
[2754154.480] compiled for 1.11.4, module version = 1.0.0
[2754154.480] ABI class: X.Org Server Extension, version 6.0
[2754154.481] (==) AIGLX enabled
[2754154.482] (II) Loading extension GLX
[2754154.482] (II) LoadModule: "record"
[2754154.487] (II) Loading /usr/X11R6/lib/modules/extensions/librecord.so
[2754154.491] (II) Module record: vendor="X.Org Foundation"
[2754154.491] compiled for 1.11.4, module version = 1.13.0
[2754154.491] Module class: X.Org Server Extension
[2754154.491] ABI class: X.Org Server Extension, version 6.0
[2754154.491] (II) Loading extension RECORD
[2754154.491] (II) LoadModule: "dri"
[2754154.497] (II) Loading /usr/X11R6/lib/modules/extensions/libdri.so
[2754154.503] (II) Module dri: vendor="X.Org Foundation"
[2754154.503] compiled for 1.11.4, module version = 1.0.0
[2754154.503] ABI class: X.Org Server Extension, version 6.0
[2754154.504] (II) Loading extension XFree86-DRI
[2754154.505] (II) LoadModule: "dri2"
[2754154.510] (II) Loading /usr/X11R6/lib/modules/extensions/libdri2.so
[2754154.514] (II) Module dri2: vendor="X.Org Foundation"
[2754154.514] compiled for 1.11.4, module version = 1.2.0
[2754154.514] ABI class: X.Org Server Extension, version 6.0
[2754154.514] (II) Loading extension DRI2
[2754154.514] (==) Matched geode as autoconfigured driver 0
[2754154.514] (==) Matched vesa as autoconfigured driver 1
[2754154.515] (==) Assigned the driver to the xf86ConfigLayout
[2754154.515] (II) LoadModule: "geode"
[2754154.517] (II) Loading /usr/X11R6/lib/modules/drivers/geode_drv.so
[2754154.528] (II) Module geode: vendor="X.Org Foundation"
[2754154.529] compiled for 1.11.4, module version = 2.11.12
[2754154.529] Module class: X.Org Video Driver
[2754154.529] ABI class: X.Org Video Driver, version 11.0
[2754154.530] (II) LoadModule: "vesa"
[2754154.534] (II) Loading /usr/X11R6/lib/modules/drivers/vesa_drv.so
[2754154.537] (II) Module vesa: vendor="X.Org Foundation"
[2754154.537] compiled for 1.11.4, module version = 2.3.0
[2754154.537] Module class: X.Org Video Driver
[2754154.537] ABI class: X.Org Video Driver, version 11.0
[2754154.537] (II) GEODE: Driver for AMD Geode Chipsets: Geode LX, Geode GX
[2754154.538] (II) VESA: driver for VESA chipsets: vesa
[2754154.538] AmdPciProbe: Probing for supported devices!
[2754154.538] (II) Loading /usr/X11R6/lib/modules/drivers/geode_drv.so
[2754154.539] (WW) Falling back to old probe method for vesa
[2754154.540] (WW) GEODE(0): Failed to set write-combining range (0xc001e,0x12)
[2754154.541] (II) Loading sub module "vgahw"
[2754154.541] (II) LoadModule: "vgahw"
[2754154.552] (II) Loading /usr/X11R6/lib/modules/libvgahw.so
[2754154.556] (II) Module vgahw: vendor="X.Org Foundation"
[2754154.556] compiled for 1.11.4, module version = 0.1.0
[2754154.556] ABI class: X.Org Video Driver, version 11.0
[2754154.558] (II) GEODE(0): Creating default Display subsection in Screen
section
"Default Screen Section" for depth/fbbpp 16/16
[2754154.558] (==) GEODE(0): Depth 16, (==) framebuffer bpp 16
[2754154.558] (==) GEODE(0): RGB weight 565
[2754154.559] (==) GEODE(0): Default visual is TrueColor
[2754154.559] (==) GEODE(0): Using gamma correction (1.0, 1.0, 1.0)
[2754154.563] (==) GEODE(0): No DCON is present
[2754154.563] (II) GEODE(0): LX output options:
[2754154.563] (II) GEODE(0): CRT: YES
[2754154.563] (II) GEODE(0): PANEL: NO
[2754154.563] (II) GEODE(0): DCON: NO
[2754154.564] (II) GEODE(0): VGA: YES
[2754154.564] (II) Loading sub module "int10"
[2754154.564] (II) LoadModule: "int10"
[2754154.571] (II) Loading /usr/X11R6/lib/modules/libint10.so
[2754154.581] (II) Module int10: vendor="X.Org Foundation"
[2754154.581] compiled for 1.11.4, module version = 1.0.0
[2754154.581] ABI class: X.Org Video Driver, version 11.0
[2754154.582] (==) GEODE(0): Write-combining range (0xa0000,0x20000) was
already clear
[2754154.582] (==) GEODE(0): Write-combining range (0xc0000,0x40000) was
already clear
[2754154.586] (II) GEODE(0): Primary V_BIOS segment is: 0xc000
[2754154.586] (==) GEODE(0): Write-combining range (0x0,0x1000) was already
clear
[2754154.587] (II) GEODE(0): 800000 bytes of video memory is less then optimal
[2754154.587] (II) GEODE(0): when compression is on. Disabling compression.
[2754154.589] (II) GEODE(0): Output default has no monitor section
[2754154.591] (II) GEODE(0): I2C bus "CS5536 DDC" initialized.
[2754154.592] (II) GEODE(0): I2C device "CS5536 DDC:ddc2" registered at address
0xA0.
[2754154.674] (II) GEODE(0): EDID for output default
[2754154.674] (II) GEODE(0): Manufacturer: ENC Model: 1690 Serial#: 0
[2754154.674] (II) GEODE(0): Year: 2003 Week: 17
[2754154.674] (II) GEODE(0): EDID Version: 1.2
[2754154.674] (II) GEODE(0): Analog Display Input, Input Voltage Level:
0.700/0.700 V
[2754154.675] (II) GEODE(0): Sync: Separate
[2754154.675] (II) GEODE(0): Max Image Size [cm]: horiz.: 34 vert.: 27
[2754154.675] (II) GEODE(0): Gamma: 2.20
[2754154.675] (II) GEODE(0): DPMS capabilities: StandBy Suspend Off; RGB/Color
Display
[2754154.675] (II) GEODE(0): First detailed timing is preferred mode
[2754154.675] (II) GEODE(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY:
0.600
[2754154.675] (II) GEODE(0): blueX: 0.150 blueY: 0.060 whiteX: 0.313 whiteY:
0.329
[2754154.675] (II) GEODE(0): Supported established timings:
[2754154.675] (II) GEODE(0): 720x400@70Hz
[2754154.675] (II) GEODE(0): 640x480@60Hz
[2754154.675] (II) GEODE(0): 640x480@67Hz
[2754154.675] (II) GEODE(0): 640x480@72Hz
[2754154.675] (II) GEODE(0): 640x480@75Hz
[2754154.675] (II) GEODE(0): 800x600@56Hz
[2754154.675] (II) GEODE(0): 800x600@60Hz
[2754154.676] (II) GEODE(0): 800x600@72Hz
[2754154.676] (II) GEODE(0): 800x600@75Hz
[2754154.676] (II) GEODE(0): 832x624@75Hz
[2754154.676] (II) GEODE(0): 1024x768@60Hz
[2754154.676] (II) GEODE(0): 1024x768@70Hz
[2754154.676] (II) GEODE(0): 1024x768@75Hz
[2754154.676] (II) GEODE(0): 1280x1024@75Hz
[2754154.676] (II) GEODE(0): 1152x864@75Hz
[2754154.676] (II) GEODE(0): Manufacturer's mask: 0
[2754154.676] (II) GEODE(0): Supported standard timings:
[2754154.676] (II) GEODE(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid:
32897
[2754154.676] (II) GEODE(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[2754154.676] (II) GEODE(0): #2: hsize: 1280 vsize 960 refresh: 75 vid: 20353
[2754154.676] (II) GEODE(0): #3: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[2754154.676] (II) GEODE(0): Supported detailed timing:
[2754154.677] (II) GEODE(0): clock: 108.0 MHz Image Size: 337 x 270 mm
[2754154.677] (II) GEODE(0): h_active: 1280 h_sync: 1328 h_sync_end 1440
h_blank_end 1688 h_border: 0
[2754154.677] (II) GEODE(0): v_active: 1024 v_sync: 1025 v_sync_end 1028
v_blanking: 1066 v_border: 0
[2754154.677] (II) GEODE(0): Serial No: 25397053
[2754154.677] (II) GEODE(0): Ranges: V min: 50 V max: 75 Hz, H min: 24 H max:
80 kHz, PixClock max 145 MHz
[2754154.677] (II) GEODE(0): Monitor name: L557
[2754154.677] (II) GEODE(0): EDID (in hex):
[2754154.677] (II) GEODE(0): 00ffffffffffff0015c3901600000000
[2754154.677] (II) GEODE(0): 110d010268221b78eaee95a3544c9926
[2754154.677] (II) GEODE(0): 0f5054bfef8081808140814f714f0101
[2754154.677] (II) GEODE(0): 010101010101302a009851002a403070
[2754154.678] (II) GEODE(0): 1300510e1100001e000000ff00323533
[2754154.678] (II) GEODE(0): 39373035330a20202020000000fd0032
[2754154.678] (II) GEODE(0): 4b18500e000a202020202020000000fc
[2754154.678] (II) GEODE(0): 004c3535370a202020202020202000da
[2754154.678] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754154.680] (II) GEODE(0): Using EDID range info for horizontal sync
[2754154.680] (II) GEODE(0): Using EDID range info for vertical refresh
[2754154.680] (II) GEODE(0): Printing DDC gathered Modelines:
[2754154.680] (II) GEODE(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440
1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[2754154.680] (II) GEODE(0): Modeline "800x600"x0.0 40.00 800 840 968 1056
600 601 605 628 +hsync +vsync (37.9 kHz)
[2754154.680] (II) GEODE(0): Modeline "800x600"x0.0 36.00 800 824 896 1024
600 601 603 625 +hsync +vsync (35.2 kHz)
[2754154.680] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 656 720 840
480 481 484 500 -hsync -vsync (37.5 kHz)
[2754154.680] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 664 704 832
480 489 492 520 -hsync -vsync (37.9 kHz)
[2754154.680] (II) GEODE(0): Modeline "640x480"x0.0 30.24 640 704 768 864
480 483 486 525 -hsync -vsync (35.0 kHz)
[2754154.681] (II) GEODE(0): Modeline "640x480"x0.0 25.18 640 656 752 800
480 490 492 525 -hsync -vsync (31.5 kHz)
[2754154.681] (II) GEODE(0): Modeline "720x400"x0.0 28.32 720 738 846 900
400 412 414 449 -hsync +vsync (31.5 kHz)
[2754154.681] (II) GEODE(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440
1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[2754154.681] (II) GEODE(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136
1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[2754154.681] (II) GEODE(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184
1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[2754154.681] (II) GEODE(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184
1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[2754154.681] (II) GEODE(0): Modeline "832x624"x0.0 57.28 832 864 928 1152
624 625 628 667 -hsync -vsync (49.7 kHz)
[2754154.682] (II) GEODE(0): Modeline "800x600"x0.0 49.50 800 816 896 1056
600 601 604 625 +hsync +vsync (46.9 kHz)
[2754154.682] (II) GEODE(0): Modeline "800x600"x0.0 50.00 800 856 976 1040
600 637 643 666 +hsync +vsync (48.1 kHz)
[2754154.682] (II) GEODE(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344
1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[2754154.682] (II) GEODE(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488
1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[2754154.682] (II) GEODE(0): Modeline "1280x960"x75.0 129.86 1280 1368 1504
1728 960 961 964 1002 -hsync +vsync (75.2 kHz)
[2754154.682] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754154.683] (II) GEODE(0): Printing probed modes for output default
[2754154.683] (II) GEODE(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440
1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[2754154.683] (II) GEODE(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440
1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[2754154.683] (II) GEODE(0): Modeline "1280x960"x75.0 129.86 1280 1368 1504
1728 960 961 964 1002 -hsync +vsync (75.2 kHz)
[2754154.683] (II) GEODE(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488
1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[2754154.683] (II) GEODE(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344
1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[2754154.684] (II) GEODE(0): Modeline "1024x768"x75.0 78.75 1024 1040 1136
1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[2754154.684] (II) GEODE(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184
1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[2754154.684] (II) GEODE(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184
1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[2754154.684] (II) GEODE(0): Modeline "832x624"x74.6 57.28 832 864 928 1152
624 625 628 667 -hsync -vsync (49.7 kHz)
[2754154.684] (II) GEODE(0): Modeline "800x600"x72.2 50.00 800 856 976 1040
600 637 643 666 +hsync +vsync (48.1 kHz)
[2754154.684] (II) GEODE(0): Modeline "800x600"x75.0 49.50 800 816 896 1056
600 601 604 625 +hsync +vsync (46.9 kHz)
[2754154.684] (II) GEODE(0): Modeline "800x600"x60.3 40.00 800 840 968 1056
600 601 605 628 +hsync +vsync (37.9 kHz)
[2754154.684] (II) GEODE(0): Modeline "800x600"x56.2 36.00 800 824 896 1024
600 601 603 625 +hsync +vsync (35.2 kHz)
[2754154.685] (II) GEODE(0): Modeline "640x480"x75.0 31.50 640 656 720 840
480 481 484 500 -hsync -vsync (37.5 kHz)
[2754154.685] (II) GEODE(0): Modeline "640x480"x72.8 31.50 640 664 704 832
480 489 492 520 -hsync -vsync (37.9 kHz)
[2754154.685] (II) GEODE(0): Modeline "640x480"x66.7 30.24 640 704 768 864
480 483 486 525 -hsync -vsync (35.0 kHz)
[2754154.685] (II) GEODE(0): Modeline "640x480"x59.9 25.18 640 656 752 800
480 490 492 525 -hsync -vsync (31.5 kHz)
[2754154.685] (II) GEODE(0): Modeline "720x400"x70.1 28.32 720 738 846 900
400 412 414 449 -hsync +vsync (31.5 kHz)
[2754154.685] (II) GEODE(0): Output default connected
[2754154.685] (II) GEODE(0): Using exact sizes for initial modes
[2754154.685] (II) GEODE(0): Output default using initial mode 1280x1024
[2754154.686] (II) GEODE(0): Using default gamma of (1.0, 1.0, 1.0) unless
otherwise stated.
[2754154.686] (--) GEODE(0): Virtual size is 1280x1280 (pitch 0)
[2754154.686] (**) GEODE(0): Driver mode "1280x1024": 108.0 MHz (scaled from
0.0 MHz), 64.0 kHz, 60.0 Hz
[2754154.686] (II) GEODE(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440
1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[2754154.686] (**) GEODE(0): Driver mode "1280x1024": 135.0 MHz (scaled from
0.0 MHz), 80.0 kHz, 75.0 Hz
[2754154.686] (II) GEODE(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440
1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[2754154.686] (**) GEODE(0): Driver mode "1280x960": 129.9 MHz (scaled from
0.0 MHz), 75.2 kHz, 75.0 Hz
[2754154.686] (II) GEODE(0): Modeline "1280x960"x75.0 129.86 1280 1368 1504
1728 960 961 964 1002 -hsync +vsync (75.2 kHz)
[2754154.687] (**) GEODE(0): Driver mode "1280x960": 108.0 MHz (scaled from
0.0 MHz), 60.0 kHz, 60.0 Hz
[2754154.687] (II) GEODE(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488
1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[2754154.687] (**) GEODE(0): Driver mode "1152x864": 108.0 MHz (scaled from
0.0 MHz), 67.5 kHz, 75.0 Hz
[2754154.687] (II) GEODE(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344
1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[2754154.687] (**) GEODE(0): Driver mode "1024x768": 78.8 MHz (scaled from 0.0
MHz), 60.0 kHz, 75.0 Hz
[2754154.687] (II) GEODE(0): Modeline "1024x768"x75.0 78.75 1024 1040 1136
1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[2754154.687] (**) GEODE(0): Driver mode "1024x768": 75.0 MHz (scaled from 0.0
MHz), 56.5 kHz, 70.1 Hz
[2754154.687] (II) GEODE(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184
1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[2754154.687] (**) GEODE(0): Driver mode "1024x768": 65.0 MHz (scaled from 0.0
MHz), 48.4 kHz, 60.0 Hz
[2754154.688] (II) GEODE(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184
1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[2754154.688] (**) GEODE(0): Driver mode "832x624": 57.3 MHz (scaled from 0.0
MHz), 49.7 kHz, 74.6 Hz
[2754154.688] (II) GEODE(0): Modeline "832x624"x74.6 57.28 832 864 928 1152
624 625 628 667 -hsync -vsync (49.7 kHz)
[2754154.688] (**) GEODE(0): Driver mode "800x600": 50.0 MHz (scaled from 0.0
MHz), 48.1 kHz, 72.2 Hz
[2754154.688] (II) GEODE(0): Modeline "800x600"x72.2 50.00 800 856 976 1040
600 637 643 666 +hsync +vsync (48.1 kHz)
[2754154.688] (**) GEODE(0): Driver mode "800x600": 49.5 MHz (scaled from 0.0
MHz), 46.9 kHz, 75.0 Hz
[2754154.688] (II) GEODE(0): Modeline "800x600"x75.0 49.50 800 816 896 1056
600 601 604 625 +hsync +vsync (46.9 kHz)
[2754154.688] (**) GEODE(0): Driver mode "800x600": 40.0 MHz (scaled from 0.0
MHz), 37.9 kHz, 60.3 Hz
[2754154.688] (II) GEODE(0): Modeline "800x600"x60.3 40.00 800 840 968 1056
600 601 605 628 +hsync +vsync (37.9 kHz)
[2754154.689] (**) GEODE(0): Driver mode "800x600": 36.0 MHz (scaled from 0.0
MHz), 35.2 kHz, 56.2 Hz
[2754154.689] (II) GEODE(0): Modeline "800x600"x56.2 36.00 800 824 896 1024
600 601 603 625 +hsync +vsync (35.2 kHz)
[2754154.689] (**) GEODE(0): Driver mode "640x480": 31.5 MHz (scaled from 0.0
MHz), 37.5 kHz, 75.0 Hz
[2754154.689] (II) GEODE(0): Modeline "640x480"x75.0 31.50 640 656 720 840
480 481 484 500 -hsync -vsync (37.5 kHz)
[2754154.689] (**) GEODE(0): Driver mode "640x480": 31.5 MHz (scaled from 0.0
MHz), 37.9 kHz, 72.8 Hz
[2754154.689] (II) GEODE(0): Modeline "640x480"x72.8 31.50 640 664 704 832
480 489 492 520 -hsync -vsync (37.9 kHz)
[2754154.689] (**) GEODE(0): Driver mode "640x480": 30.2 MHz (scaled from 0.0
MHz), 35.0 kHz, 66.7 Hz
[2754154.689] (II) GEODE(0): Modeline "640x480"x66.7 30.24 640 704 768 864
480 483 486 525 -hsync -vsync (35.0 kHz)
[2754154.689] (**) GEODE(0): Driver mode "640x480": 25.2 MHz (scaled from 0.0
MHz), 31.5 kHz, 59.9 Hz
[2754154.689] (II) GEODE(0): Modeline "640x480"x59.9 25.18 640 656 752 800
480 490 492 525 -hsync -vsync (31.5 kHz)
[2754154.690] (**) GEODE(0): Driver mode "720x400": 28.3 MHz (scaled from 0.0
MHz), 31.5 kHz, 70.1 Hz
[2754154.690] (II) GEODE(0): Modeline "720x400"x70.1 28.32 720 738 846 900
400 412 414 449 -hsync +vsync (31.5 kHz)
[2754154.690] (**) GEODE(0): Display dimensions: (340, 270) mm
[2754154.690] (**) GEODE(0): DPI set to (95, 120)
[2754154.690] (II) Loading sub module "fb"
[2754154.690] (II) LoadModule: "fb"
[2754154.698] (II) Loading /usr/X11R6/lib/modules/libfb.so
[2754154.704] (II) Module fb: vendor="X.Org Foundation"
[2754154.704] compiled for 1.11.4, module version = 1.0.0
[2754154.704] ABI class: X.Org ANSI C Emulation, version 0.4
[2754154.704] (II) Loading sub module "exa"
[2754154.704] (II) LoadModule: "exa"
[2754154.712] (II) Loading /usr/X11R6/lib/modules/libexa.so
[2754154.717] (II) Module exa: vendor="X.Org Foundation"
[2754154.717] compiled for 1.11.4, module version = 2.5.0
[2754154.717] ABI class: X.Org Video Driver, version 11.0
[2754154.717] (II) UnloadModule: "vesa"
[2754154.717] (II) Unloading vesa
[2754154.718] (==) GEODE(0): Write-combining range (0xa0000,0x10000) was
already clear
[2754154.718] (II) GEODE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0,
hwp->PIOOffset is 0x0000
[2754154.719] (WW) GEODE(0): Failed to set write-combining range
(0xf0000,0x10000)
[2754154.719] (II) GEODE(0): Geode LX video memory 600000 bytes at 0x8a7ae000
[2754154.719] (II) GEODE(0): LX video memory:
[2754154.719] (II) GEODE(0): Display: 0x320000 bytes
[2754154.719] (II) GEODE(0): Cursor: 0x3000 bytes
[2754154.720] (II) GEODE(0): ExaBfrSz: 0x40000 bytes
[2754154.720] (II) GEODE(0): EXA: 0x19d000 bytes
[2754154.720] (II) GEODE(0): FREE: 0x0 bytes
[2754154.794] (II) EXA(0): Offscreen pixmap area of 1691648 bytes
[2754154.796] (II) EXA(0): Driver registered support for the following
operations:
[2754154.796] (II) Solid
[2754154.796] (II) Copy
[2754154.796] (II) Composite (RENDER acceleration)
[2754154.796] (==) GEODE(0): Backing store disabled
[2754154.805] (==) GEODE(0): DPMS enabled
[2754154.807] (II) GEODE(0): RandR 1.2 enabled, ignore the following RandR
disabled message.
[2754154.810] (--) RandR disabled
[2754154.810] (II) Initializing built-in extension Generic Event Extension
[2754154.810] (II) Initializing built-in extension SHAPE
[2754154.810] (II) Initializing built-in extension MIT-SHM
[2754154.810] (II) Initializing built-in extension XInputExtension
[2754154.810] (II) Initializing built-in extension XTEST
[2754154.810] (II) Initializing built-in extension BIG-REQUESTS
[2754154.810] (II) Initializing built-in extension SYNC
[2754154.810] (II) Initializing built-in extension XKEYBOARD
[2754154.811] (II) Initializing built-in extension XC-MISC
[2754154.811] (II) Initializing built-in extension SECURITY
[2754154.811] (II) Initializing built-in extension XINERAMA
[2754154.811] (II) Initializing built-in extension XFIXES
[2754154.811] (II) Initializing built-in extension RENDER
[2754154.811] (II) Initializing built-in extension RANDR
[2754154.811] (II) Initializing built-in extension COMPOSITE
[2754154.811] (II) Initializing built-in extension DAMAGE
[2754154.933] (II) AIGLX: Screen 0 is not DRI2 capable
[2754154.933] (II) AIGLX: Screen 0 is not DRI capable
[2754155.085] (II) AIGLX: Loaded and initialized swrast
[2754155.085] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[2754155.090] (II) GEODE(0): Setting screen physical size to 338 x 270
[2754157.202] (II) config/wscons: checking input device /dev/wskbd
[2754157.202] (II) wskbd: using layout de
[2754157.202] (II) wskbd: using variant nodeadkeys
[2754157.202] (II) LoadModule: "kbd"
[2754157.209] (II) Loading /usr/X11R6/lib/modules/input/kbd_drv.so
[2754157.212] (II) Module kbd: vendor="X.Org Foundation"
[2754157.212] compiled for 1.11.4, module version = 1.6.1
[2754157.212] Module class: X.Org XInput Driver
[2754157.212] ABI class: X.Org XInput driver, version 13.0
[2754157.212] (II) Using input driver 'kbd' for '/dev/wskbd'
[2754157.212] (II) Loading /usr/X11R6/lib/modules/input/kbd_drv.so
[2754157.213] (**) /dev/wskbd: always reports core events
[2754157.213] (**) /dev/wskbd: always reports core events
[2754157.213] (**) Option "Protocol" "standard"
[2754157.214] (**) Option "XkbRules" "base"
[2754157.214] (**) Option "XkbModel" "pc105"
[2754157.214] (**) Option "XkbLayout" "de"
[2754157.214] (**) Option "XkbVariant" "nodeadkeys"
[2754157.214] (II) XINPUT: Adding extended input device "/dev/wskbd" (type:
KEYBOARD, id 6)
[2754157.942] (II) config/wscons: checking input device /dev/wsmouse
[2754157.942] (II) LoadModule: "ws"
[2754157.949] (II) Loading /usr/X11R6/lib/modules/input/ws_drv.so
[2754157.952] (II) Module ws: vendor="X.Org Foundation"
[2754157.952] compiled for 1.11.4, module version = 1.3.0
[2754157.952] Module class: X.Org XInput Driver
[2754157.952] ABI class: X.Org XInput driver, version 13.0
[2754157.952] (II) Using input driver 'ws' for '/dev/wsmouse'
[2754157.953] (II) Loading /usr/X11R6/lib/modules/input/ws_drv.so
[2754157.953] (**) /dev/wsmouse: always reports core events
[2754157.953] (II) ws: /dev/wsmouse: debuglevel 0
[2754157.953] (**) Option "Device" "/dev/wsmouse"
[2754157.953] (**) ws: /dev/wsmouse: ZAxisMapping: buttons 4 and 5
[2754157.954] (**) ws: /dev/wsmouse: WAxisMapping: buttons 6 and 7
[2754157.954] (**) ws: /dev/wsmouse: associated screen: 0
[2754158.405] (II) ws: /dev/wsmouse: minimum x position: 0
[2754158.405] (II) ws: /dev/wsmouse: maximum x position: 1279
[2754158.405] (II) ws: /dev/wsmouse: minimum y position: 0
[2754158.406] (II) ws: /dev/wsmouse: maximum y position: 1023
[2754158.406] (==) ws: /dev/wsmouse: Buttons: 7
[2754158.406] (**) ws: /dev/wsmouse: YAxisMapping: buttons 4 and 5
[2754158.406] (II) XINPUT: Adding extended input device "/dev/wsmouse" (type:
MOUSE, id 7)
[2754158.865] (**) /dev/wsmouse: (accel) keeping acceleration scheme 1
[2754158.865] (**) /dev/wsmouse: (accel) acceleration profile 0
[2754158.865] (**) /dev/wsmouse: (accel) acceleration factor: 2.000
[2754158.865] (**) /dev/wsmouse: (accel) acceleration threshold: 4
[2754169.867] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754169.868] (II) GEODE(0): Using hsync ranges from config file
[2754169.868] (II) GEODE(0): Using vrefresh ranges from config file
[2754169.868] (II) GEODE(0): Printing DDC gathered Modelines:
[2754169.868] (II) GEODE(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440
1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[2754169.868] (II) GEODE(0): Modeline "800x600"x0.0 40.00 800 840 968 1056
600 601 605 628 +hsync +vsync (37.9 kHz)
[2754169.868] (II) GEODE(0): Modeline "800x600"x0.0 36.00 800 824 896 1024
600 601 603 625 +hsync +vsync (35.2 kHz)
[2754169.868] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 656 720 840
480 481 484 500 -hsync -vsync (37.5 kHz)
[2754169.868] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 664 704 832
480 489 492 520 -hsync -vsync (37.9 kHz)
[2754169.868] (II) GEODE(0): Modeline "640x480"x0.0 30.24 640 704 768 864
480 483 486 525 -hsync -vsync (35.0 kHz)
[2754169.868] (II) GEODE(0): Modeline "640x480"x0.0 25.18 640 656 752 800
480 490 492 525 -hsync -vsync (31.5 kHz)
[2754169.869] (II) GEODE(0): Modeline "720x400"x0.0 28.32 720 738 846 900
400 412 414 449 -hsync +vsync (31.5 kHz)
[2754169.869] (II) GEODE(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440
1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[2754169.869] (II) GEODE(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136
1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[2754169.869] (II) GEODE(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184
1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[2754169.869] (II) GEODE(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184
1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[2754169.869] (II) GEODE(0): Modeline "832x624"x0.0 57.28 832 864 928 1152
624 625 628 667 -hsync -vsync (49.7 kHz)
[2754169.869] (II) GEODE(0): Modeline "800x600"x0.0 49.50 800 816 896 1056
600 601 604 625 +hsync +vsync (46.9 kHz)
[2754169.869] (II) GEODE(0): Modeline "800x600"x0.0 50.00 800 856 976 1040
600 637 643 666 +hsync +vsync (48.1 kHz)
[2754169.870] (II) GEODE(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344
1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[2754169.870] (II) GEODE(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488
1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[2754169.870] (II) GEODE(0): Modeline "1280x960"x75.0 129.86 1280 1368 1504
1728 960 961 964 1002 -hsync +vsync (75.2 kHz)
[2754169.870] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754183.328] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754183.329] (II) GEODE(0): Using hsync ranges from config file
[2754183.329] (II) GEODE(0): Using vrefresh ranges from config file
[2754183.329] (II) GEODE(0): Printing DDC gathered Modelines:
[2754183.329] (II) GEODE(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440
1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[2754183.329] (II) GEODE(0): Modeline "800x600"x0.0 40.00 800 840 968 1056
600 601 605 628 +hsync +vsync (37.9 kHz)
[2754183.329] (II) GEODE(0): Modeline "800x600"x0.0 36.00 800 824 896 1024
600 601 603 625 +hsync +vsync (35.2 kHz)
[2754183.330] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 656 720 840
480 481 484 500 -hsync -vsync (37.5 kHz)
[2754183.330] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 664 704 832
480 489 492 520 -hsync -vsync (37.9 kHz)
[2754183.330] (II) GEODE(0): Modeline "640x480"x0.0 30.24 640 704 768 864
480 483 486 525 -hsync -vsync (35.0 kHz)
[2754183.330] (II) GEODE(0): Modeline "640x480"x0.0 25.18 640 656 752 800
480 490 492 525 -hsync -vsync (31.5 kHz)
[2754183.330] (II) GEODE(0): Modeline "720x400"x0.0 28.32 720 738 846 900
400 412 414 449 -hsync +vsync (31.5 kHz)
[2754183.330] (II) GEODE(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440
1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[2754183.330] (II) GEODE(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136
1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[2754183.330] (II) GEODE(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184
1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[2754183.331] (II) GEODE(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184
1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[2754183.331] (II) GEODE(0): Modeline "832x624"x0.0 57.28 832 864 928 1152
624 625 628 667 -hsync -vsync (49.7 kHz)
[2754183.331] (II) GEODE(0): Modeline "800x600"x0.0 49.50 800 816 896 1056
600 601 604 625 +hsync +vsync (46.9 kHz)
[2754183.331] (II) GEODE(0): Modeline "800x600"x0.0 50.00 800 856 976 1040
600 637 643 666 +hsync +vsync (48.1 kHz)
[2754183.331] (II) GEODE(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344
1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[2754183.331] (II) GEODE(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488
1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[2754183.331] (II) GEODE(0): Modeline "1280x960"x75.0 129.86 1280 1368 1504
1728 960 961 964 1002 -hsync +vsync (75.2 kHz)
[2754183.331] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754225.829] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754225.829] (II) GEODE(0): Using hsync ranges from config file
[2754225.829] (II) GEODE(0): Using vrefresh ranges from config file
[2754225.829] (II) GEODE(0): Printing DDC gathered Modelines:
[2754225.829] (II) GEODE(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440
1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[2754225.829] (II) GEODE(0): Modeline "800x600"x0.0 40.00 800 840 968 1056
600 601 605 628 +hsync +vsync (37.9 kHz)
[2754225.830] (II) GEODE(0): Modeline "800x600"x0.0 36.00 800 824 896 1024
600 601 603 625 +hsync +vsync (35.2 kHz)
[2754225.830] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 656 720 840
480 481 484 500 -hsync -vsync (37.5 kHz)
[2754225.830] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 664 704 832
480 489 492 520 -hsync -vsync (37.9 kHz)
[2754225.830] (II) GEODE(0): Modeline "640x480"x0.0 30.24 640 704 768 864
480 483 486 525 -hsync -vsync (35.0 kHz)
[2754225.830] (II) GEODE(0): Modeline "640x480"x0.0 25.18 640 656 752 800
480 490 492 525 -hsync -vsync (31.5 kHz)
[2754225.830] (II) GEODE(0): Modeline "720x400"x0.0 28.32 720 738 846 900
400 412 414 449 -hsync +vsync (31.5 kHz)
[2754225.830] (II) GEODE(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440
1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[2754225.830] (II) GEODE(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136
1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[2754225.831] (II) GEODE(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184
1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[2754225.831] (II) GEODE(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184
1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[2754225.831] (II) GEODE(0): Modeline "832x624"x0.0 57.28 832 864 928 1152
624 625 628 667 -hsync -vsync (49.7 kHz)
[2754225.831] (II) GEODE(0): Modeline "800x600"x0.0 49.50 800 816 896 1056
600 601 604 625 +hsync +vsync (46.9 kHz)
[2754225.831] (II) GEODE(0): Modeline "800x600"x0.0 50.00 800 856 976 1040
600 637 643 666 +hsync +vsync (48.1 kHz)
[2754225.831] (II) GEODE(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344
1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[2754225.831] (II) GEODE(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488
1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[2754225.831] (II) GEODE(0): Modeline "1280x960"x75.0 129.86 1280 1368 1504
1728 960 961 964 1002 -hsync +vsync (75.2 kHz)
[2754225.832] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754292.922] (II) GEODE(0): EDID vendor "ENC", prod id 5776
[2754292.922] (II) GEODE(0): Using hsync ranges from config file
[2754292.922] (II) GEODE(0): Using vrefresh ranges from config file
[2754292.922] (II) GEODE(0): Printing DDC gathered Modelines:
[2754292.922] (II) GEODE(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440
1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[2754292.922] (II) GEODE(0): Modeline "800x600"x0.0 40.00 800 840 968 1056
600 601 605 628 +hsync +vsync (37.9 kHz)
[2754292.922] (II) GEODE(0): Modeline "800x600"x0.0 36.00 800 824 896 1024
600 601 603 625 +hsync +vsync (35.2 kHz)
[2754292.923] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 656 720 840
480 481 484 500 -hsync -vsync (37.5 kHz)
[2754292.923] (II) GEODE(0): Modeline "640x480"x0.0 31.50 640 664 704 832
480 489 492 520 -hsync -vsync (37.9 kHz)
[2754292.923] (II) GEODE(0): Modeline "640x480"x0.0 30.24 640 704 768 864
480 483 486 525 -hsync -vsync (35.0 kHz)
[2754292.923] (II) GEODE(0): Modeline "640x480"x0.0 25.18 640 656 752 800
480 490 492 525 -hsync -vsync (31.5 kHz)
[2754292.923] (II) GEODE(0): Modeline "720x400"x0.0 28.32 720 738 846 900
400 412 414 449 -hsync +vsync (31.5 kHz)
[2754292.923] (II) GEODE(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440
1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[2754292.923] (II) GEODE(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136
1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[2754292.924] (II) GEODE(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184
1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[2754292.924] (II) GEODE(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184
1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[2754292.924] (II) GEODE(0): Modeline "832x624"x0.0 57.28 832 864 928 1152
624 625 628 667 -hsync -vsync (49.7 kHz)
[2754292.924] (II) GEODE(0): Modeline "800x600"x0.0 49.50 800 816 896 1056
600 601 604 625 +hsync +vsync (46.9 kHz)
[2754292.924] (II) GEODE(0): Modeline "800x600"x0.0 50.00 800 856 976 1040
600 637 643 666 +hsync +vsync (48.1 kHz)
[2754292.924] (II) GEODE(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344
1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[2754292.924] (II) GEODE(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488
1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[2754292.924] (II) GEODE(0): Modeline "1280x960"x75.0 129.86 1280 1368 1504
1728 960 961 964 1002 -hsync +vsync (75.2 kHz)
[2754292.925] (II) GEODE(0): EDID vendor "ENC", prod id 5776
