>Synopsis: can't install 24/10/2012 i386 snapshot on Dell PowerEdge SC430
>: kernel: protection fault trap, code=0
>Category: kernel i386
>Environment:
System : OpenBSD 5.2
Details : OpenBSD 5.2-current (RAMDISK_CD) #54: Wed Oct 24 09:19:52
MDT 2012
[email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
Architecture: OpenBSD.i386
Machine : i386
>Description:
The 24/10/2012 i386 snapshot don't boot on my dell poweredge SC430, either on
cdrom or hard drive.
Here is the bsd.rd boot log :
OpenBSD/i386 BOOT 3.18
boot> bsd.rd
booting hd0a:bsd.rd: 5986168+958376 [52+231328+219761]=0x70dadc
entry point at 0x200120
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2012 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.2-current (RAMDISK_CD) #54: Wed Oct 24 09:19:52 MDT 2012
[email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel(R) Pentium(R) D CPU 2.80GHz ("GenuineIntel" 686-class)fatal
protection fault (4) in supervisor mode
trap type 4 code 0 eip d048c57e cs 8 eflags 10012 cr2 0 cpl 0
panic: trap type 4, code=0, pc=d048c57e
fatal page fault (6) in supervisor mode
trap type 6 code 0 eip d02f81a7 cs 8 eflags 10046 cr2 c cpl 0
panic: trap type 6, code=0, pc=d02f81a7
fatal page fault (6) in supervisor mode
[last 3 lines repeated 77 times]
trap type 6 code 0 eip d02f81a7 cs 8 eflags 10046 cr2 c cpl 0
panic: trap type 6, code=0, pc=d02f81a7
fatal page fault (6) in supervisor mode
trap type 6 code 0 eip d03b073c cs 8 eflags 10002 cr2 540 cpl 0
panic: trap type 6, code=0, pc=d03b073c
fatal page fault (6) in supervisor mode
trap type 6 code 0 eip d02f81a7 cs 8 eflags 10046 cr2 c cpl 0
panic: trap type 6, code=0, pc=d02f81a7
fatal stray interrupt 2
page fault (6) in supervisor mode
trap type 6 code 0 eip d02f81a7 cs 8 eflags 10046 cr2 c cpl 0
panic: trap type 6, code=0, pc=d02f81a7
fatal pag
I've tried the bsd.mp :
>> OpenBSD/i386 BOOT 3.18
boot> bsd.mp.20121024
booting hd0a:bsd.mp.20121024: 8396388+1102532 [52+380336+366943]=0x9c59e0
entry point at 0x200120
[ using 747704 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2012 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.2-current (GENERIC.MP) #73: Wed Oct 24 09:13:20 MDT 2012
[email protected]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Pentium(R) D CPU 2.80GHz ("GenuineIntel" 686-class)kernel:
protection fault trap, code=0
Stopped at calibrate_cyclecounter+0x9a: rdmsr
calibrate_cyclecounter(d08d47b7,d0b0c8f4,d0a7cc00,d09db044,d09b047f) at calibra
te_cyclecounter+0x9a
identifycpu(d0b0c8e0,d08fb809,10,0,ffffffff) at identifycpu+0x1f5
cpu_startup(d0a557c8,d08d6960,c0,d0bc7f4c,2) at cpu_startup+0xc8
main(d02004d9,d02004e1,0,0,0) at main+0x7f
ddb{0}> ps
PID PPID PGRP UID S FLAGS WAIT COMMAND
ddb{0}> show registers
ds 0x10
es 0x10
fs 0x20
gs 0
edi 0x38d
esi 0xd0b0c8f4 cpu_info_primary+0x14
ebp 0xd0bc7e68 end+0xb8c20
ebx 0xd08fb900 _length_code+0x1a40
edx 0xd0b0c8e0 cpu_info_primary
ecx 0x38d
eax 0x40
eip 0xd07623fa calibrate_cyclecounter+0x9a
cs 0x8
eflags 0x10012
esp 0xd0bc7e30 end+0xb8be8
ss 0x10
calibrate_cyclecounter+0x9a: rdmsr
ddb{0}>
The 10-Sep-2012 snapshot work fine on this computer (which I use to send the
bug report).
The 24-Oct-2012 snapshot boot without problem on a Dell Vostro 1310 laptop.
>How-To-Repeat:
On my computer (Dell PowerEdge SC430) it appends every time.
>Fix:
I have no clue.
dmesg:
OpenBSD 5.2-current (GENERIC.MP) #19: Mon Sep 10 07:54:14 MDT 2012
[email protected]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Pentium(R) D CPU 2.80GHz ("GenuineIntel" 686-class) 2.80 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,NXE,LONG,SSE3,DTES64,MWAIT,DS-CPL,CNXT-ID,CX16,xTPR,LAHF
real mem = 2145501184 (2046MB)
avail mem = 2099519488 (2002MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 10/06/06, BIOS32 rev. 0 @ 0xffe90, SMBIOS
rev. 2.3 @ 0xf0450 (60 entries)
bios0: vendor Dell Inc. version "A04" date 10/06/2006
bios0: Dell Inc. PowerEdge SC430
acpi0 at bios0: rev 2
acpi0: sleep states S0 S1 S4 S5
acpi0: tables DSDT FACP SSDT APIC BOOT ASF! MCFG HPET
acpi0: wakeup devices VBTN(S4) PCI0(S5) PCI4(S5) PCI2(S5) PCI3(S5) PCI1(S5)
PCI5(S5) PCI6(S5) MOU_(S1) USB0(S1) USB1(S1) USB2(S1) USB3(S1)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 199MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Pentium(R) D CPU 2.80GHz ("GenuineIntel" 686-class) 2.80 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,NXE,LONG,SSE3,DTES64,MWAIT,DS-CPL,CNXT-ID,CX16,xTPR,LAHF
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 8
acpimcfg0 at acpi0 addr 0xd0000000, bus 0-63
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 5 (PCI4)
acpiprt1 at acpi0: bus 2 (PCI2)
acpiprt2 at acpi0: bus -1 (PCI3)
acpiprt3 at acpi0: bus 1 (PCI1)
acpiprt4 at acpi0: bus 3 (PCI5)
acpiprt5 at acpi0: bus 4 (PCI6)
acpiprt6 at acpi0: bus 0 (PCI0)
acpicpu0 at acpi0
acpicpu1 at acpi0
acpibtn0 at acpi0: VBTN
bios0: ROM list: 0xc0000/0xf800 0xcf800/0x2000! 0xd1800/0x2800
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel E7230 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "Intel E7230 PCIE" rev 0x00: apic 8 int 16
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: apic 8 int 16
pci2 at ppb1 bus 2
vga1 at pci2 dev 0 function 0 "ATI Radeon HD 4350" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
radeondrm0 at vga1: apic 8 int 16
drm0 at radeondrm0
azalia0 at pci2 dev 0 function 1 "ATI Radeon HD 4000 HD Audio" rev 0x00: msi
azalia0: no supported codecs
ppb2 at pci0 dev 28 function 4 "Intel 82801G PCIE" rev 0x01: apic 8 int 16
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 5 "Intel 82801G PCIE" rev 0x01: apic 8 int 17
pci4 at ppb3 bus 4
bge0 at pci4 dev 0 function 0 "Broadcom BCM5751" rev 0x01, BCM5750 A1 (0x4001):
apic 8 int 17, address 00:13:72:20:b7:84
brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: apic 8 int 21
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 8 int 22
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: apic 8 int 18
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: apic 8 int 23
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 8 int 21
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xe1
pci5 at ppb4 bus 5
rl0 at pci5 dev 4 function 0 "Realtek 8139" rev 0x10: apic 8 int 16, address
00:e0:4c:10:0f:5c
rlphy0 at rl0 phy 0: RTL internal PHY
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
pciide0: channel 0 ignored (disabled)
pciide0: channel 1 ignored (disabled)
pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 8 int 20 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <WDC WD800JD-75MSA3>
wd0: 16-sector PIO, LBA48, 76293MB, 156250000 sectors
atapiscsi0 at pciide1 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <PBDS, DVD+-RW DH-16W1S, 2D14> ATAPI 5/cdrom
removable
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
cd0(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 5
wd1 at pciide1 channel 1 drive 0: <ST3500413AS>
wd1: 16-sector PIO, LBA48, 476940MB, 976773168 sectors
wd1(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 6
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: apic 8 int 17
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM ECC PC2-4200CL3
spdmem1 at iic0 addr 0x52: 1GB DDR2 SDRAM ECC PC2-4200CL3
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
mtrr: Pentium Pro MTRR support
uhub5 at uhub0 port 2 "Standard Microsystems Hub" rev 2.00/0.01 addr 2
uhidev0 at uhub5 port 2 configuration 1 interface 0 "TypeMatrix.com USB
Keyboard" rev 1.10/1.30 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub5 port 2 configuration 1 interface 1 "TypeMatrix.com USB
Keyboard" rev 1.10/1.30 addr 3
uhidev1: iclass 3/1, 3 report ids
uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=2, output=0, feature=0
uhid2 at uhidev1 reportid 3: input=2, output=1, feature=0
uhidev2 at uhub5 port 4 configuration 1 interface 0 "Primax Electronics USB
Optical Mouse" rev 2.00/2.00 addr 4
uhidev2: iclass 3/1
ums0 at uhidev2: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
uaudio0 at uhub4 port 2 configuration 1 interface 0 "Ten X Technology, Inc. USB
AUDIO" rev 1.10/1.0b addr 2
uaudio0: audio rev 1.00, 4 mixer controls
audio0 at uaudio0
uhidev3 at uhub4 port 2 configuration 1 interface 3 "Ten X Technology, Inc. USB
AUDIO" rev 1.10/1.0b addr 2
uhidev3: iclass 3/1
uhid3 at uhidev3: input=8, output=8, feature=0
uhidev4 at uhub4 port 2 configuration 1 interface 4 "Ten X Technology, Inc. USB
AUDIO" rev 1.10/1.0b addr 2
uhidev4: iclass 3/1, 3 report ids
uhid4 at uhidev4 reportid 3: input=1, output=0, feature=0
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on wd0a swap on wd0b dump on wd0b
usbdevs:
Controller /dev/usb0:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
Intel(0x8086), rev 1.00
port 1 powered
port 2 addr 2: high speed, self powered, config 1, Hub(0x2504), Standard
Microsystems(0x0424), rev 0.01
port 1 powered
port 2 addr 3: low speed, power 100 mA, config 1, USB Keyboard(0x2030),
TypeMatrix.com(0x1e54), rev 1.30
port 3 powered
port 4 addr 4: low speed, power 98 mA, config 1, USB Optical Mouse(0x4d81),
Primax Electronics(0x0461), rev 2.00
port 3 powered
port 4 powered
port 5 powered
port 6 powered
port 7 powered
port 8 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb2:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb3:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb4:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
port 1 powered
port 2 addr 2: full speed, power 500 mA, config 1, USB AUDIO(0xf211), Ten X
Technology, Inc.(0x1130), rev 1.0b
