I'm attempting a fresh install with the 12/28 snapshot. The drive in
question had the first 100 MB zeroed out by dd prior to install. It
appears to attempt a whole-disk install, fail in a couple ways (read
error, pdisk, newfs), and then continue on with looping OpenBSD-area
attempts until I kill it.
The hardware in question is newly-acquired, so I can't rule out a
drive issue, but it autoinstalls without problem on 5.8-release.
Thanks for your time.
install.conf, ai.log, dmesg follow:
----- install.conf -----
System hostname = build
Password for root account = $2b$09$...
Do you expect to run the X Window System = no
Setup a user = bconway
Full name for user = Brian Conway
Password for user = $2b$10$...
What timezone are you in = UTC
Use (W)hole disk = W
Location of sets = http
HTTP Server = mirror.esc7.net
Set name(s) = -game* -x*
----- ai.log -----
System hostname? (short form, e.g. 'foo') build
Available network interfaces are: gem0 vlan0.
Which network interface do you wish to configure? (or 'done') [gem0] gem0
IPv4 address for gem0? (or 'dhcp' or 'none') [dhcp] dhcp
DHCPREQUEST on gem0 to 255.255.255.255
DHCPACK from 10.10.10.1 (02:00:00:00:00:00)
bound to 10.10.10.100 -- renewal in 21600 seconds.
IPv6 address for gem0? (or 'rtsol' or 'none') [none] none
Available network interfaces are: gem0 vlan0.
Which network interface do you wish to configure? (or 'done') [done] done
Using DNS domainname int.rcesoftware.com
Using DNS nameservers at 10.10.10.1
Password for root account? <provided>
Public ssh key for root account? [none] none
Start sshd(8) by default? [yes] yes
Do you want the X Window System to be started by xdm(1)? [no] no
Change the default console to zstty0? [no] no
Setup a user? (enter a lower-case loginname, or 'no') [no] bconway
Full name for user bconway? [bconway] Brian Conway
Password for user bconway? <provided>
Public ssh key for user bconway [none] none
WARNING: root is targeted by password guessing attacks, pubkeys are safer.
Allow root ssh login? (yes, no, prohibit-password) [no] no
What timezone are you in? ('?' for list) [UTC] UTC
Available disks are: wd0.
Which disk is the root disk? ('?' for details) [wd0] wd0
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
pdisk: No valid block 1 on '/dev/wd0c'
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
pdisk: No valid block 1 on '/dev/wd0c'
MBR has invalid signature; not showing it.
Use (W)hole disk or (E)dit the MBR? [whole] W
Creating a 1MB DOS partition and an OpenBSD partition for rest of
wd0...1+0 records in
1+0 records out
1048576 bytes transferred in 0.091 secs (11448336 bytes/sec)
done.
newfs_msdos: /dev/rwd0i: Device not configured
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
pdisk: No valid block 1 on '/dev/wd0c'
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
pdisk: No valid block 1 on '/dev/wd0c'
Disk: wd0 geometry: 155061/16/63 [156301488 Sectors]
Offset: 0 Signature: 0xAA55
Starting Ending LBA Info:
#: id C H S - C H S [ start: size ]
-------------------------------------------------------------------------------
0: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
1: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
2: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
3: A6 1 0 17 - 155060 15 63 [ 1024: 156300464 ] OpenBSD
Use (W)hole disk, use the (O)penBSD area or (E)dit the MBR? [OpenBSD] OpenBSD
newfs_msdos: /dev/rwd0i: Device not configured
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
read failed
----- dmesg -----
console out [ATY,RockHopper2_A] console in [keyboard], using USB
using parent ATY,RockHopper2Paren:: memaddr 98000000, size 8000000 :
consaddr 9c008000 : ioaddr 90020000, size 20000: width 1024 linebytes
1024 height 768 depth 8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.9-beta (RAMDISK) #843: Sun Dec 27 20:02:14 MST 2015
[email protected]:/usr/src/sys/arch/macppc/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1028304896 (980MB)
mainbus0 at root: model PowerMac10,2
cpu0 at mainbus0: 7447A (Revision 0x105): 1499 MHz: 512KB L2 cache
mem at mainbus0 not configured
memc0 at mainbus0: uni-n rev 0xd2
"hw-clock" at memc0 not configured
kiic0 at memc0 offset 0xf8001000
iic0 at kiic0
mpcpcibr0 at mainbus0 pci: uni-north
pci0 at mpcpcibr0 bus 0
pchb0 at pci0 dev 11 function 0 "Apple UniNorth AGP" rev 0x00
vgafb0 at pci0 dev 16 function 0 "ATI Radeon 9200" rev 0x01, mmio
wsdisplay0 at vgafb0 mux 1: console (std, vt100 emulation)
mpcpcibr1 at mainbus0 pci: uni-north
pci1 at mpcpcibr1 bus 0
macobio0 at pci1 dev 23 function 0 "Apple Intrepid" rev 0x00
openpic0 at macobio0 offset 0x40000: version 0x4614 feature 3f0302 LE
macgpio0 at macobio0 offset 0x50
"modem-reset" at macgpio0 offset 0x1d not configured
"modem-power" at macgpio0 offset 0x1c not configured
macgpio1 at macgpio0 offset 0x9: irq 47
"programmer-switch" at macgpio0 offset 0x11 not configured
"gpio5" at macgpio0 offset 0x6f not configured
"gpio6" at macgpio0 offset 0x70 not configured
"extint-gpio15" at macgpio0 offset 0x67 not configured
"escc-legacy" at macobio0 offset 0x12000 not configured
zs0 at macobio0 offset 0x13000: irq 22,23
zstty0 at zs0 channel 0
zstty1 at zs0 channel 1
"i2s" at macobio0 offset 0x10000 not configured
"timer" at macobio0 offset 0x15000 not configured
adb0 at macobio0 offset 0x16000
"i2c" at macobio0 offset 0x18000 not configured
wdc0 at macobio0 offset 0x20000 irq 24: DMA
"Broadcom BCM4318" rev 0x02 at pci1 dev 18 function 0 not configured
ohci0 at pci1 dev 26 function 0 "Apple Intrepid USB" rev 0x00: irq 29,
version 1.0, legacy support
ohci1 at pci1 dev 27 function 0 "NEC USB" rev 0x43: irq 63, version 1.0
ohci2 at pci1 dev 27 function 1 "NEC USB" rev 0x43: irq 63, version 1.0
ehci0 at pci1 dev 27 function 2 "NEC USB" rev 0x04: irq 63
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "Apple OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci2: USB revision 1.0
uhub3 at usb3 "NEC OHCI root hub" rev 1.00/1.00 addr 1
mpcpcibr2 at mainbus0 pci: uni-north
pci2 at mpcpcibr2 bus 0
kauaiata0 at pci2 dev 13 function 0 "Apple Intrepid ATA" rev 0x00
wdc1 at kauaiata0 irq 39: DMA
wd0 at wdc1 channel 0 drive 0: <ST9808211A>
wd0: 16-sector PIO, LBA, 76319MB, 156301488 sectors
atapiscsi0 at wdc1 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MATSHITA, CD-RW CW-8124, DACD> ATAPI
5/cdrom removable
wd0(wdc1:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
cd0(wdc1:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
"Apple UniNorth Firewire" rev 0x81 at pci2 dev 14 function 0 not configured
gem0 at pci2 dev 15 function 0 "Apple Uni-N2 GMAC" rev 0x80: irq 41,
address 00:11:24:d1:c1:6a
bmtphy0 at gem0 phy 0: BCM5221 100baseTX PHY, rev. 4
uhidev0 at uhub1 port 1 configuration 1 interface 0 "vendor 0x05ac
product 0x1000" rev 2.00/19.65 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev1 at uhub1 port 1 configuration 1 interface 1 "vendor 0x05ac
product 0x1000" rev 2.00/19.65 addr 2
uhidev1: iclass 3/1
uhid0 at uhidev1: input=3, output=0, feature=1
uhidev2 at uhub2 port 1 configuration 1 interface 0 "Microsoft Comfort
Curve Keyboard 3000" rev 2.00/1.70 addr 2
uhidev2: iclass 3/1
ukbd1 at uhidev2
wskbd1 at ukbd1: console keyboard, using wsdisplay0
uhidev3 at uhub2 port 1 configuration 1 interface 1 "Microsoft Comfort
Curve Keyboard 3000" rev 2.00/1.70 addr 2
uhidev3: iclass 3/0, 1 report id
uhid1 at uhidev3 reportid 1: input=7, output=0, feature=0
softraid0 at root
scsibus1 at softraid0: 256 targets
bootpath: /pci@f4000000/ata-6@d/disk@0:/59.rd
root on rd0a swap on rd0b dump on rd0b
