Hi,
same install.conf does work w/atleast bbb, panda and cubie2.
I did try several times and it always freezes like shown below.
and no problems going over manual install/upgrade w/the same board.
imxuart0 at simplebus2: console
I think i initially had the "do you want to set com0 as console"-type
of question w/= yes, but now when i looked at bbb/cubie2 log of install,
i don't see the question even coming up.
So this might irrelevant, but fwiw. imx doesn't have com0 to begin with.
-Artturi
install.conf used w/o passwords&keys:
Password for root =
Which speed should = 115200
Setup a user = aalm
Password for user =
What timezone are you in = Europe/Helsinki
Which disk is the root disk = sd0
Location of sets = nfs
Server IP address or hostname = 192.168.2.1
Filesystem on server to mount = /tmnt/exp
Use TCP transport = yes
Pathname to the sets = 6.2/armv7
Public ssh key for root account =
Public ssh key for user aalm =
U-Boot SPL 2017.09 (Sep 13 2017 - 01:57:10)
Trying to boot from MMC1
U-Boot 2017.09 (Sep 13 2017 - 01:57:10 -0600)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: Wandboard rev B1
I2C: ready
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /imx6q-wandboard-revb1.dtb
35762 bytes read in 21 ms (1.6 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
67372 bytes read in 30 ms (2.1 MiB/s)
## Starting EFI application at 12000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC: no card present
mmc_init: -123, time 2
MMC Device 2 not found
MMC Device 3 not found
Scanning disks on sata...
Found 6 disks
>> OpenBSD/armv7 BOOTARM 1.0
boot> boot bsd.rd
booting sd0a:bsd.rd: 2290956+7990812+446804 [174061+90+318688+151881]=0xad97ac
OpenBSD/armv7 booting ...
arg0 0xc0dd97ac arg1 0x0 arg2 0x18000000
Allocating page tables
freestart = 0x10dda000, free_pages = 520742 (0x0007f226)
IRQ stack: p0x10e08000 v0xc0e08000
ABT stack: p0x10e09000 v0xc0e09000
UND stack: p0x10e0a000 v0xc0e0a000
SVC stack: p0x10e0b000 v0xc0e0b000
Creating L1 page table at 0x10ddc000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 0
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.2-beta (RAMDISK) #69: Sat Sep 16 21:52:11 MDT 2017
[email protected]:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 2147483648 (2048MB)
avail mem = 2091585536 (1994MB)
mainbus0 at root: Wandboard i.MX6 Quad Board rev B1
cpu0 at mainbus0: ARM Cortex-A9 r2p10 (ARMv7)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
simplebus0 at mainbus0: "soc"
ampintc0 at simplebus0 nirq 160, ncpu 4
simplebus1 at simplebus0: "aips-bus"
imxccm0 at simplebus1: imx6 rev 1.2 CPU freq: 792 MHz
imxiomuxc0 at simplebus1
simplebus2 at simplebus1: "spba-bus"
imxuart0 at simplebus2: console
imxgpio0 at simplebus1
imxgpio1 at simplebus1
imxgpio2 at simplebus1
imxgpio3 at simplebus1
imxgpio4 at simplebus1
imxgpio5 at simplebus1
imxgpio6 at simplebus1
imxdog0 at simplebus1
simplebus3 at simplebus1: "anatop"
imxgpc0 at simplebus1
simplebus4 at simplebus0: "aips-bus"
imxehci0 at simplebus4
usb0 at imxehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "i.MX6 EHCI root hub" rev 2.00/1.00
addr 1
imxehci1 at simplebus4
usb1 at imxehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "i.MX6 EHCI root hub" rev 2.00/1.00
addr 1
fec0 at simplebus4
fec0: address 00:1f:7b:b4:04:49
atphy0 at fec0 phy 1: AR8035 10/100/1000 PHY, rev. 4
imxesdhc0 at simplebus4
imxesdhc0: 198 MHz base clock
sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
imxesdhc1 at simplebus4
imxesdhc1: 198 MHz base clock
sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
imxesdhc2 at simplebus4
imxesdhc2: 198 MHz base clock
sdmmc2 at imxesdhc2: 4-bit, mmc high-speed, dma
imxiic0 at simplebus4
iic0 at imxiic0
imxiic1 at simplebus4
iic1 at imxiic1
"fsl,sgtl5000" at iic1 addr 0xa not configured
imxocotp0 at simplebus4
imxuart1 at simplebus4
imxahci0 at simplebus0: AHCI 1.3
scsibus0 at imxahci0: 32 targets
simplebus5 at mainbus0: "regulators"
sdmmc1: can't enable card
scsibus1 at sdmmc2: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <SD/MMC, SD16G, 0030> SCSI2 0/direct removable
sd0: 14804MB, 512 bytes/sector, 30318592 sectors
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 6.2 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? a
DHCPDISCOVER on fec0 - interval 1
DHCPOFFER from 192.168.2.2 (00:22:68:10:3d:f0)
DHCPREQUEST on fec0 to 255.255.255.255
DHCPACK from 192.168.2.2 (00:22:68:10:3d:f0)
bound to 192.168.2.88 -- renewal in 21600 seconds.
Fetching http://192.168.2.2/00:1f:7b:b4:04:49-install.conf?path=snapshots/armv7
Fetching http://192.168.2.2/av7wandb-install.conf?path=snapshots/armv7
Fetching http://192.168.2.2/install.conf?path=snapshots/armv7
Performing non-interactive install...
Terminal type? [vt220] vt220
System hostname? (short form, e.g. 'foo') [av7wandb] av7wandb
