On Tue, Oct 10, 2017 at 12:53:54PM +0300, Artturi Alm wrote:
> Hi,
>
> same install.conf does work w/atleast bbb, panda and cubie2.
> I did try several times and it always freezes like shown below.
> and no problems going over manual install/upgrade w/the same board.
>
> imxuart0 at simplebus2: console
>
> I think i initially had the "do you want to set com0 as console"-type
> of question w/= yes, but now when i looked at bbb/cubie2 log of install,
> i don't see the question even coming up.
> So this might irrelevant, but fwiw. imx doesn't have com0 to begin with.
>
> -Artturi
>
Hi,
noticed this difference on : console reporting:
pandaboard-es:
com0 at simplebus0: ti16750, 64 byte fifo
com0: probed fifo depth: 0 bytes
com1 at simplebus0: ti16750, 64 byte fifo
com1: probed fifo depth: 0 bytes
com2 at simplebus0: ti16750, 64 byte fifo
com2: console
com3 at simplebus0: ti16750, 64 byte fifo
com3: probed fifo depth: 0 bytes
beagleboneblack:
com0 at simplebus0: ti16750, 64 byte fifo
com0: console
cubieboard2:
com0 at simplebus0: ns16550, no working fifo
com0: console
wandboard:
imxuart0 at simplebus2: console
imxuart1 at simplebus4
i honestly don't want to stare at this long enough figure it out
if this is related or not given above difference.
src/distrib/miniroot/install.sub:
3165 # Scan /var/run/dmesg.boot for console device.
3166 CONSOLE=$(scan_dmesg '/^\([^ ]*\).*: console$/s//\1/p')
3167 [[ -n $CONSOLE ]] && CSPEED=$(stty speed </dev/console)
i do saw how armv7 install.md has only this:
md_consoleinfo() {
}
so it's likely not helping out in this situation.
to anyone looking at this, thanks in advance:)
-Artturi
>
> install.conf used w/o passwords&keys:
>
> Password for root =
> Which speed should = 115200
> Setup a user = aalm
> Password for user =
> What timezone are you in = Europe/Helsinki
> Which disk is the root disk = sd0
> Location of sets = nfs
> Server IP address or hostname = 192.168.2.1
> Filesystem on server to mount = /tmnt/exp
> Use TCP transport = yes
> Pathname to the sets = 6.2/armv7
> Public ssh key for root account =
> Public ssh key for user aalm =
>
>
>
> U-Boot SPL 2017.09 (Sep 13 2017 - 01:57:10)
> Trying to boot from MMC1
>
>
> U-Boot 2017.09 (Sep 13 2017 - 01:57:10 -0600)
>
> CPU: Freescale i.MX6Q rev1.2 at 792 MHz
> Reset cause: POR
> Board: Wandboard rev B1
> I2C: ready
> DRAM: 2 GiB
> MMC: FSL_SDHC: 0, FSL_SDHC: 1
> *** Warning - bad CRC, using default environment
>
> No panel detected: default to HDMI
> Display: HDMI (1024x768)
> In: serial
> Out: serial
> Err: serial
> Net: FEC [PRIME]
> Hit any key to stop autoboot: 0
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc 0:1...
> reading /imx6q-wandboard-revb1.dtb
> 35762 bytes read in 21 ms (1.6 MiB/s)
> Found EFI removable media binary efi/boot/bootarm.efi
> reading efi/boot/bootarm.efi
> 67372 bytes read in 30 ms (2.1 MiB/s)
> ## Starting EFI application at 12000000 ...
> Scanning disks on usb...
> Scanning disks on mmc...
> MMC: no card present
> mmc_init: -123, time 2
> MMC Device 2 not found
> MMC Device 3 not found
> Scanning disks on sata...
> Found 6 disks
> >> OpenBSD/armv7 BOOTARM 1.0
> boot> boot bsd.rd
> booting sd0a:bsd.rd: 2290956+7990812+446804 [174061+90+318688+151881]=0xad97ac
>
> OpenBSD/armv7 booting ...
> arg0 0xc0dd97ac arg1 0x0 arg2 0x18000000
> Allocating page tables
> freestart = 0x10dda000, free_pages = 520742 (0x0007f226)
> IRQ stack: p0x10e08000 v0xc0e08000
> ABT stack: p0x10e09000 v0xc0e09000
> UND stack: p0x10e0a000 v0xc0e0a000
> SVC stack: p0x10e0b000 v0xc0e0b000
> Creating L1 page table at 0x10ddc000
> Mapping kernel
> Constructing L2 page tables
> undefined page pmap board type: 0
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2017 OpenBSD. All rights reserved. https://www.OpenBSD.org
>
> OpenBSD 6.2-beta (RAMDISK) #69: Sat Sep 16 21:52:11 MDT 2017
> [email protected]:/usr/src/sys/arch/armv7/compile/RAMDISK
> real mem = 2147483648 (2048MB)
> avail mem = 2091585536 (1994MB)
> mainbus0 at root: Wandboard i.MX6 Quad Board rev B1
> cpu0 at mainbus0: ARM Cortex-A9 r2p10 (ARMv7)
> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
> cortex0 at mainbus0
> amptimer0 at cortex0: tick rate 396000 KHz
> armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
> simplebus0 at mainbus0: "soc"
> ampintc0 at simplebus0 nirq 160, ncpu 4
> simplebus1 at simplebus0: "aips-bus"
> imxccm0 at simplebus1: imx6 rev 1.2 CPU freq: 792 MHz
> imxiomuxc0 at simplebus1
> simplebus2 at simplebus1: "spba-bus"
> imxuart0 at simplebus2: console
> imxgpio0 at simplebus1
> imxgpio1 at simplebus1
> imxgpio2 at simplebus1
> imxgpio3 at simplebus1
> imxgpio4 at simplebus1
> imxgpio5 at simplebus1
> imxgpio6 at simplebus1
> imxdog0 at simplebus1
> simplebus3 at simplebus1: "anatop"
> imxgpc0 at simplebus1
> simplebus4 at simplebus0: "aips-bus"
> imxehci0 at simplebus4
> usb0 at imxehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "i.MX6 EHCI root hub" rev 2.00/1.00
> addr 1
> imxehci1 at simplebus4
> usb1 at imxehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "i.MX6 EHCI root hub" rev 2.00/1.00
> addr 1
> fec0 at simplebus4
> fec0: address 00:1f:7b:b4:04:49
> atphy0 at fec0 phy 1: AR8035 10/100/1000 PHY, rev. 4
> imxesdhc0 at simplebus4
> imxesdhc0: 198 MHz base clock
> sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
> imxesdhc1 at simplebus4
> imxesdhc1: 198 MHz base clock
> sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
> imxesdhc2 at simplebus4
> imxesdhc2: 198 MHz base clock
> sdmmc2 at imxesdhc2: 4-bit, mmc high-speed, dma
> imxiic0 at simplebus4
> iic0 at imxiic0
> imxiic1 at simplebus4
> iic1 at imxiic1
> "fsl,sgtl5000" at iic1 addr 0xa not configured
> imxocotp0 at simplebus4
> imxuart1 at simplebus4
> imxahci0 at simplebus0: AHCI 1.3
> scsibus0 at imxahci0: 32 targets
> simplebus5 at mainbus0: "regulators"
> sdmmc1: can't enable card
> scsibus1 at sdmmc2: 2 targets, initiator 0
> sd0 at scsibus1 targ 1 lun 0: <SD/MMC, SD16G, 0030> SCSI2 0/direct removable
> sd0: 14804MB, 512 bytes/sector, 30318592 sectors
> boot device: sd0
> root on rd0a swap on rd0b dump on rd0b
> WARNING: CHECK AND RESET THE DATE!
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/armv7 6.2 installation program.
> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? a
> DHCPDISCOVER on fec0 - interval 1
> DHCPOFFER from 192.168.2.2 (00:22:68:10:3d:f0)
> DHCPREQUEST on fec0 to 255.255.255.255
> DHCPACK from 192.168.2.2 (00:22:68:10:3d:f0)
> bound to 192.168.2.88 -- renewal in 21600 seconds.
> Fetching
> http://192.168.2.2/00:1f:7b:b4:04:49-install.conf?path=snapshots/armv7
> Fetching http://192.168.2.2/av7wandb-install.conf?path=snapshots/armv7
> Fetching http://192.168.2.2/install.conf?path=snapshots/armv7
> Performing non-interactive install...
> Terminal type? [vt220] vt220
> System hostname? (short form, e.g. 'foo') [av7wandb] av7wandb
>
>
