On Wed, Dec 31, 2025 at 02:56:23AM +0300, Vitaliy Makkoveev wrote:
> My AX210 card stopped to connect to wifi networks after upgrade to the
> "Sun Dec 28 22:15:38" snapshot. The previous one was from the 30
> November and wifi worked perfectly.
> 
> Now I see only "iwx0: device timeout" even with debug enabled.
> 
> My card is: 
> 
> iwx0 at pci2 dev 0 function 0 "Intel Wi-Fi 6 AX210" rev 0x1a, msix
> iwx0: hw rev 0x420, fw 77.f92b5fed.0, pnvm ce1a5094, address
> 88:d8:2e:ba:b3:d7
> 

Sorry, I mean I see no errors  in debug output. According log, the card
performs association, but in fact it does not:


driver status:
  tx ring  0: qid=0  cur=54  cur_hw=54  queued=0  
  tx ring  1: qid=1  cur=0   cur_hw=0   queued=0  
  tx ring  2: qid=2  cur=0   cur_hw=0   queued=0  
  tx ring  3: qid=3  cur=0   cur_hw=0   queued=0  
  tx ring  4: qid=4  cur=0   cur_hw=0   queued=0  
  tx ring  5: qid=5  cur=0   cur_hw=0   queued=0  
  tx ring  6: qid=6  cur=0   cur_hw=0   queued=0  
  tx ring  7: qid=7  cur=0   cur_hw=0   queued=0  
  tx ring  8: qid=8  cur=0   cur_hw=0   queued=0  
  tx ring  9: qid=9  cur=0   cur_hw=0   queued=0  
  rx ring: cur=428
  802.11 state SCAN
iwx0: SCAN -> INIT
iwx0: begin active scan
iwx0: INIT -> SCAN
iwx0: end active scan
iwx0: - 0a:0b:0c:0d:0e:0f    6   +13 54M   ess  privacy   rsn! "wifi_help"!
iwx0: + 11:22:33:44:55:66    2   +42 54M   ess  privacy   rsn  "myap"
iwx0: - 1a:1b:1c:1d:1e:1f   12   +33 54M   ess  privacy   rsn  "Room"!
iwx0: firmware has detected regulatory domain 'RU' (0x5255)
iwx0: SCAN -> AUTH
iwx0: sending auth to 11:22:33:44:55:66 on channel 2 mode 11g
iwx0: AUTH -> ASSOC
iwx0: sending assoc_req to 11:22:33:44:55:66 on channel 2 mode 11g
iwx0: ASSOC -> RUN
iwx0: associated with 11:22:33:44:55:66 ssid "myap" channel 2 start MCS 0 short 
preamble short slot time HT enabled
iwx0: missed beacon threshold set to 30 beacons, beacon interval is 100 TU

$ ifconfig iwx0
iwx0: flags=8947<UP,BROADCAST,DEBUG,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
        lladdr aa:bb:cc:dd:ee:ff
        index 1 priority 4 llprio 3
        trunk: trunkdev trunk0
        groups: wlan
        media: IEEE802.11 autoselect (HT-MCS11 mode 11n)
        status: no network
        ieee80211: join myap chan 2 bssid 11:22:33:44:55:66 59% wpakey 
wpaprotos wpa2 wpaakms psk,sha256-psk wpaciphers ccmp wpagroupcipher ccmp

Reply via email to