On Wed, Dec 31, 2025 at 12:19:15PM +0100, Stefan Sperling wrote:
> On Wed, Dec 31, 2025 at 12:09:06AM +0000, Vitaliy Makkoveev wrote:
> > Sorry, I mean I see no errors in debug output. According log, the card
> > performs association, but in fact it does not:
>
> Please send the full firmware error trace.
> Above "driver status" there should be lines which show firmware error
> details. These details include the hex code of the last command received
> by firmware, an important detail which is missing from this bug report.
>
It has no errors, but I see "device timeout". The previous kernel from
November 30 works fine with this AP.
iwx0: SCAN -> SCAN
iwx0: device timeout
iwx0: dumping device error log
iwx0: errlog not found, skipping
> Are you able to re-configure the AP? If so, are there any settings related
> to management frame encryption (PMF/MFP) or WPA3 which you can change to
> see if this makes any difference?
>
This is an old TP-Link N450. It has no such ability.
iwx0: hw rev 0x420, fw 77.f92b5fed.0, pnvm ce1a5094, address aa:bb:cc:dd:ee:ff
iwx0: RUN -> ASSOC
iwx0: sending assoc_req to 01:01:01:01:01:01 on channel 2 mode 11n
iwx0: association timed out for 01:01:01:01:01:01
iwx0: ASSOC -> SCAN
iwx0: end active scan
iwx0: best AP 01:01:01:01:01:01 "myap" score 53
iwx0: switching to network "myap"
iwx0: - ---- AP list ----
iwx0: - ---- AP list ----
iwx0: firmware has detected regulatory domain 'RU' (0x5255)
iwx0: SCAN -> SCAN
iwx0: end active scan
iwx0: - ---- AP list ----
iwx0: - ---- AP list ----
iwx0: firmware has detected regulatory domain 'RU' (0x5255)
iwx0: SCAN -> SCAN
iwx0: device timeout
iwx0: dumping device error log
iwx0: errlog not found, skipping
driver status:
tx ring 0: qid=0 cur=52 cur_hw=52 queued=0
tx ring 1: qid=1 cur=0 cur_hw=0 queued=0
tx ring 2: qid=2 cur=0 cur_hw=0 queued=0
tx ring 3: qid=3 cur=0 cur_hw=0 queued=0
tx ring 4: qid=4 cur=0 cur_hw=0 queued=0
tx ring 5: qid=5 cur=0 cur_hw=0 queued=0
tx ring 6: qid=6 cur=0 cur_hw=0 queued=0
tx ring 7: qid=7 cur=0 cur_hw=0 queued=0
tx ring 8: qid=8 cur=0 cur_hw=0 queued=0
tx ring 9: qid=9 cur=0 cur_hw=0 queued=0
rx ring: cur=347
802.11 state SCAN
iwx0: SCAN -> INIT
iwx0: begin active scan
iwx0: INIT -> SCAN
iwx0: end active scan
iwx0: - ---- AP list ----
iwx0: - ---- AP list ----
iwx0: + 01:01:01:01:01:01 2 +38 54M ess privacy rsn "myap"
iwx0: firmware has detected regulatory domain 'RU' (0x5255)
iwx0: SCAN -> AUTH
iwx0: sending auth to 01:01:01:01:01:01 on channel 2 mode 11g
iwx0: AUTH -> ASSOC
iwx0: sending assoc_req to 01:01:01:01:01:01 on channel 2 mode 11g
iwx0: ASSOC -> RUN
iwx0: associated with 01:01:01:01:01:01 ssid "myap" channel 2 start MCS
0 short preamble long slot time protection enabled HT enabled
iwx0: missed beacon threshold set to 30 beacons, beacon interval is 100 TU
$ ifconfig iwx0
iwx0: flags=8947<UP,BROADCAST,DEBUG,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr aa:bb:cc:dd:ee:ff
index 1 priority 4 llprio 3
trunk: trunkdev trunk0
groups: wlan
media: IEEE802.11 autoselect (HT-MCS3 mode 11n)
status: no network
ieee80211: join myap chan 2 bssid 01:02:02:04:05:06 61% wpakey
wpaprotos wpa2 wpaakms psk,sha256-psk wpaciphers ccmp wpagroupcipher ccmp
