Hi Louis, In Oxford we mostly use CentOS -- I've made a few installations following the instructions at https://casper.ssl.berkeley.edu/wiki/Xilinx_ISE_11.4_Setup and everything has been relatively painless. I've also got a Fedora compile machine that seem to work OK, so that's also an option.
Cheers, Jack On 13 July 2011 23:49, Louis Dartez <[email protected]> wrote: > ** > Hello, > > So then it seems I may be needing to switch operating > systems. I am currently using XUBUNTU 11.04. Guessing this is probably my > problem. Any recommendations? I'm thinking CentOS... > > - Louis Dartez > (956) 372-5812 > > Arecibo Remote Command Center Scholar > Center for Gravitational Wave Astronomy > University of Texas at Brownsville > > > On 7/13/11 5:32 PM, Jack Hickish wrote: > > Hi Louis, > > The error you describe sounds similar to that encountered when trying to > compile on Ubuntu -- see here: > http://www.mail-archive.com/[email protected]/msg01224.html > > Are you using Centos/RHEL/one of the supported OSs? > > Cheers, > > Jack > > On 13 July 2011 23:10, Louis Dartez <[email protected]> wrote: > >> Hi Mark, >> >> I tried running ctrl-D and updating my design and then >> re-compiling with 'bee_xps' (version 1.1). The compilation process crashed >> once more with the exact same message in the dialogue box as before. The >> output within the MATLAB command window is as follows: >> >> >> Detected Linux OS >> ############################# >> ## System Update ## >> ############################# >> Warning: The model 'tutorial1_revisited' does not have continuous states, >> hence Simulink is using the solver 'VariableStepDiscrete' instead of >> solver 'ode45'. You can disable this diagnostic by explicitly specifying >> a discrete solver in the solver tab of the Configuration Parameters >> dialog, or by setting the 'Automatic solver parameter selection' >> diagnostic to 'none' in the Diagnostics tab of the Configuration >> Parameters dialog. >> > In gen_xps_files at 199 >> >> In bee_xps>run_Callback at 150 >> In bee_xps at 82 >> Warning: Using a default value of 0.2 for maximum step size. The >> simulation step size will be equal to or less than this value. You can >> disable this diagnostic by setting 'Automatic solver parameter selection' >> diagnostic to 'none' in the Diagnostics page of the configuration >> parameters dialog. >> > In gen_xps_files at 199 >> >> In bee_xps>run_Callback at 150 >> In bee_xps at 82 >> ############################# >> ## Block objects creation ## >> ############################# >> ###################### >> ## Checking objects ## >> ###################### >> Running system generator ... >> Warning: The model 'tutorial1_revisited' does not have continuous states, >> hence Simulink is using the solver 'VariableStepDiscrete' instead of >> solver 'ode45'. You can disable this diagnostic by explicitly specifying >> a discrete solver in the solver tab of the Configuration Parameters >> dialog, or by setting the 'Automatic solver parameter selection' >> diagnostic to 'none' in the Diagnostics tab of the Configuration >> Parameters dialog. >> > In >> /opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlCompileGenerateMdl.p>xlCompileGenerateMdl >> at 181 >> In >> /opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlGenerateButton.p>xlGenerateButton >> at 281 >> In gen_xps_files at 324 >> In bee_xps>run_Callback at 150 >> In bee_xps at 82 >> Warning: Using a default value of 0.2 for maximum step size. The >> simulation step size will be equal to or less than this value. You can >> disable this diagnostic by setting 'Automatic solver parameter >> selection' diagnostic to 'none' in the Diagnostics page of the >> configuration parameters dialog. >> > In >> /opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlCompileGenerateMdl.p>xlCompileGenerateMdl >> at 181 >> In >> /opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlGenerateButton.p>xlGenerateButton >> at 281 >> In gen_xps_files at 324 >> In bee_xps>run_Callback at 150 >> In bee_xps at 82 >> >> >> >> >> >> I'm at a complete loss as to what may be causing this problem. If you (or >> anyone else reading this) know of any other troubleshooting procedures that >> may help pin down the problem it would be greatly appreciated. >> >> Thanks, >> >> Louis >> >> >> >> On Mon, Jul 11, 2011 at 2:01 PM, Mark Wagner <[email protected]>wrote: >> >>> Hi Louis, >>> >>> Can you run control-D to update the design? This will propagate the >>> data types >>> and may give you some idea where the issue lies. >>> >>> Mark >>> >>> >>> On Fri, Jul 8, 2011 at 9:27 PM, Louis Dartez <[email protected]>wrote: >>> >>>> >>>> Hello, >>>> >>>> I've been trying to compile tutorial 1 using the bee_xps >>>> command on MATLAB. After waiting a while I get a dialogue box titled 'NGC >>>> Netlisting Error' with the following errors: >>>> >>>> [: 21: >>>> >>>> /opt/Xilinx/11.1/ISE/lib/lin64:/opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/lib: >>>> /usr/local/MATLAB/R2009a/sys/os/glnxa64:/usr/local/MATLAB/R2009a/bin/glnxa64:/usr/local/MATLAB/R2009a/extern/lib/glnxa64:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64/native_threads:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64:/opt/Xilinx/11.1/ISE/bin/lin64: >>>> unexpected operator >>>> >>>> [: 22: >>>> >>>> /opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/lib:/opt/Xilinx/11.1/ISE/lib/lin64: >>>> /opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/lib:/usr/local/MATLAB/R2009a/sys/os/glnxa64:/usr/local/MATLAB/R2009a/bin/glnxa64:/usr/local/MATLAB/R2009a/extern/lib/glnxa64:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64/native_threads:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64/server:/usr/local/MATLAB/R2009a/sys/java/jre/glnxa64/jre/lib/amd64:/opt/Xilinx/11.1/ISE/bin/lin64: >>>> unexpected operator >>>> >>>> In addition to the dialogue box above, I'm getting the following output >>>> within the MATLAB prompt: >>>> >>>> > In >>>> /opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlCompileGenerateMdl.p>xlCompileGenerateMdl >>>> at 181 >>>> In >>>> /opt/Xilinx/11.1/DSP_Tools/lin64/sysgen/bin/xlGenerateButton.p>xlGenerateButton >>>> at 281 >>>> In gen_xps_files at 324 >>>> In bee_xps>run_Callback at 150 >>>> In bee_xps at 82 >>>> Error using ==> gen_xps_files at 328 >>>> XSG generation failed: >>>> >>>> Any Ideas as to what may be behind these errors? Any advice would be >>>> appreciated. >>>> >>>> Thanks, >>>> >>> -- >> -- Louis Dartez >> (956) 372-5812 >> Arecibo Remote Command Center Scholar >> Center for Gravitational Wave Astronomy >> University of Texas at Brownsville >> >> >>> -- >>>> -- Louis Dartez >>>> (956) 372-5812 <%28956%29%20372-5812> >>>> Arecibo Remote Command Center Scholar >>>> Center for Gravitational Wave Astronomy >>>> University of Texas at Brownsville >>>> >>> >>> >> >> >> >> >
