Hi Indrajit, I know this thread is now old, but FYI, I updated that repository with the UC Berkeley ROACH1 and ROACH2 configurations. Apologies for being so very very slow about it.
Cheers Jack On Wed, 20 Feb 2019 at 06:26, Jack Hickish <[email protected]> wrote: > > Oh, sorry, I completely misread your email. > > I don't think that link will work. I think we have a working netboot setup in > Berkeley. I can make sure it works and then post it to github. That'll have > to be next week though, currently I'm hiding in an observatory. > > Cheers > Jack > > On Wed, 20 Feb 2019 at 16:00, indrajit <[email protected]> wrote: >> >> Hi Jack, >> >> I am looking for ROACH1 . I went through this link I thought Its for ROACH2. >> >> I will give a try. >> >> Thanks and regards >> >> indrajit >> >> >> On Wednesday 20 February 2019 07:26 PM, Jack Hickish wrote: >> >> Hi Indrajit, >> >> Does the filesystem at https://github.com/casper-astro/roach2_nfs_uboot work >> for you? >> >> If not, let me know. >> >> Cheers >> Jack >> >> On Wed, 20 Feb 2019 at 15:42, indrajit <[email protected]> wrote: >>> >>> Hello All, >>> >>> I am trying to make a Netboot system. I went through the "ROACH NFS guide - >>> Casper" >>> >>> Downloading the kernel and file system from the bellow link is broken(not >>> available ). >>> >>> http://casper.berkeley.edu/svn/trunk/roach/sw/binaries/linux/ >>> >>> http://casper.berkeley.edu/svn/trunk/roach/sw/binaries/filesystem/ >>> >>> anyone kindly give me a link from where I can download the same. >>> >>> Thanks >>> >>> Indrajit >>> >>> >>> >>> On Wednesday 13 February 2019 07:43 PM, indrajit wrote: >>> >>> Hello James, >>> >>> Same cable , same ROACH board with same SD card but I changed the >>> machine(Ubuntu 14.04) in which I initially set the boot sequences. I could >>> able to interrupt and select the boot order (mmcboot). >>> >>> The data acquisition machine is Ubuntu 18.04 which has advanced version of >>> gtkterm and extra baud-rates functionality and etc... Might be some bug in >>> that.. >>> >>> thanks and regards >>> >>> Indrajit >>> >>> >>> >>> >>> >>> On Wednesday 13 February 2019 05:18 PM, James Smith wrote: >>> >>> Hello Indrajit, >>> >>> Check the settings on your serial connection - did you turn off Flow >>> Control? >>> >>> Regards, >>> James >>> >>> >>> On Wed, Feb 13, 2019 at 1:47 PM indrajit <[email protected]> wrote: >>>> >>>> Hello James, >>>> >>>> I am also doing the same. I am able to see the booting sequences via the >>>> serial terminal counting down from 10 and I am trying to interrupt but the >>>> keystrokes are not interrupting the boot menu. >>>> >>>> Even I changed the SD card which is logically nothing to do with the >>>> booting sequence. >>>> >>>> Thanks and regards >>>> >>>> Indrajit >>>> >>>> >>>> >>>> On Wednesday 13 February 2019 05:07 PM, James Smith wrote: >>>> >>>> Hello Indrajit, >>>> >>>> Why were you not able to interrupt the process? Connect to the ROACH via >>>> the serial port then reset it - you should be able then to see the place >>>> to interrupt and set netboot (or whatever else you need) quite easily. >>>> >>>> Regards, >>>> James >>>> >>>> >>>> On Wed, Feb 13, 2019 at 1:31 PM indrajit <[email protected]> wrote: >>>>> >>>>> Hello all, >>>>> >>>>> A new ROACH1 while taking measurements stopped responding. Then via >>>>> serial communication, found that it got booted using the flash. >>>>> Restarted and trying to interrupt using the serial terminal and boot via >>>>> MMC-BOOT. I couldn't interrupt using the keyboard. I inserted another >>>>> working SD card and tried the same. Failed to boot via the memory card. >>>>> >>>>> Thanks and regards >>>>> >>>>> indrajit >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google Groups >>>>> "[email protected]" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send an >>>>> email to [email protected]. >>>>> To post to this group, send email to [email protected]. >>>> >>>> -- >>>> You received this message because you are subscribed to the Google Groups >>>> "[email protected]" group. >>>> To unsubscribe from this group and stop receiving emails from it, send an >>>> email to [email protected]. >>>> To post to this group, send email to [email protected]. >>>> >>>> >>>> -- >>>> You received this message because you are subscribed to the Google Groups >>>> "[email protected]" group. >>>> To unsubscribe from this group and stop receiving emails from it, send an >>>> email to [email protected]. >>>> To post to this group, send email to [email protected]. >>> >>> -- >>> You received this message because you are subscribed to the Google Groups >>> "[email protected]" group. >>> To unsubscribe from this group and stop receiving emails from it, send an >>> email to [email protected]. >>> To post to this group, send email to [email protected]. >>> >>> >>> >>> -- >>> You received this message because you are subscribed to the Google Groups >>> "[email protected]" group. >>> To unsubscribe from this group and stop receiving emails from it, send an >>> email to [email protected]. >>> To post to this group, send email to [email protected]. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "[email protected]" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To post to this group, send email to [email protected]. >> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "[email protected]" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To post to this group, send email to [email protected]. -- You received this message because you are subscribed to the Google Groups "[email protected]" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected].
