Hi everyone, I solved this problem by using an older version of mlib_devel. Files · edbc38236f2a756e169b74a7bad0d76263c0f91a · ALPACA / CASPER / mlib_devel · GitLab (byu.edu) <https://gitlab.ras.byu.edu/alpaca/casper/mlib_devel/-/tree/edbc38236f2a756e169b74a7bad0d76263c0f91a>
[observer@cylctrl bin]$ ruby adc16_status.rb roach8 roach8: Design built for ROACH2 rev2 with 8 ADCs (ZDOK rev2) roach8: Gateware supports demux modes (currently using demux by 1) roach8: ZDOK0 clock OK, ZDOK1 clock OK roach8: AAAABBBBCCCCDDDDEEEEFFFFGGGGHHHH roach8: 12341234123412341234123412341234 roach8: ................................ deskew roach8: ................................ sync [image: 微信图片_20230607173048.png] Wang 在2023年6月6日星期二 UTC+8 20:03:16<Wang> 写道： > Hi everyone, > > When I validated my design on ROACH2, I found that there were some issues > with the synchronization of the adc chip. > > The environment I used was ubuntu14 ise14.7 matlab2013b mlib_devel-roach2. > > The parameter of my XSG_core_config module is set to ROACH2:sx475t > adc0_clk 200MHz. > > I used david's adc16 script for initialization, and there were no errors. > > Use adc16_status.rb to view the adc channel and find that synchronization > was not successful. > > > > adc16_init.rb: > > Connecting to roach7... > > Programming roach7 with adcsync.bof... > > Design built for ROACH2 rev2 with 8 ADCs (ZDOK rev2) > > Gateware supports demux modes (using demux by 1) > > Resetting ADC, power cycling ADC, and reprogramming FPGA... > > ZDOK0 clock OK, ZDOK1 clock OK > > Calibrating SERDES blocks...ABCDEFGH > > SERDES calibration successful. > > Selecting analog inputs... > > Using default digital gain of 1... > > Done! > > > > adc16_status.rb ： > > [observer@cylctrl bin]$ ruby adc16_status.rb roach7 > > roach7: Design built for ROACH2 rev2 with 8 ADCs (ZDOK rev2) > > roach7: Gateware supports demux modes (currently using demux by 1) > > roach7: ZDOK0 clock OK, ZDOK1 clock OK > > roach7: AAAABBBBCCCCDDDDEEEEFFFFGGGGHHHH > > roach7: 12341234123412341234123412341234 > > roach7: ................................ deskew > > roach7: ....XXXXXXXX........XXXX....XXXX sync > > > > May I ask which step do you think I did not set correctly, resulting in > the failure of adc synchronization? > > Has anyone synced successfully on ROACH2 using the adc16x250-8 module? > > Could you please send me a copy of your mlib_devel? I suspect it is caused > by the version of mlib_devel. > > > > BW！ > > Wang > -- You received this message because you are subscribed to the Google Groups "[email protected]" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/41d19d40-639f-4c4b-934e-7c4fac5dc533n%40lists.berkeley.edu.
