Nicely put Marc : ) On Tue, Nov 3, 2009 at 11:15 PM, marc abel <[email protected]> wrote:
> If you are using more bandwidth than you actually have then you WILL > drop packets. There is no way around that, there is no magic QOS that > makes everything use less bandwidth. What you can do however is decide > which traffic you drop. If your RTP packets are the most important > than you can them to a gaurenteed bandwidth and then set stuff like > http, and ftp to drop first. > > On Tue, Nov 3, 2009 at 4:53 PM, VALERE BIKANDA <[email protected]> wrote: > > > > If i police on one side, i will drop RTP UDP packets. I have to configure > my > > router to to control the trafic going in and out without dropping packets > > but the trafic should not exceed the configured bandwith. I don't have > the > > control of other routers around. But the LAN users are teleconferencing > with > > a remote site on the Internet and will not allow me to drop some packets > in > > or out of the routers. Is it possible without exceeding the configured > > bandwith ? > > > > Thanks > > ________________________________ > > From: marc abel <[email protected]> > > To: VALERE BIKANDA <[email protected]> > > Cc: pra pa <[email protected]>; [email protected] > > Sent: Tue, November 3, 2009 11:24:22 PM > > Subject: Re: [OSL | CCIE_RS] Comitted access rate > > > > You can't shape inbound, you can only police. If you think about it > > shaping works by queueing things up and sending them at an average > > rate. By the time you could queue things coming in you have already > > received them so it would be pointless to try to shape them. > > > > On Tue, Nov 3, 2009 at 4:17 PM, VALERE BIKANDA <[email protected]> > wrote: > >> > >> Thanks ! > >> > >> It works ! > >> > >> But how can we apply it inbound and outbound ? > >> > >> > >> Thanks > >> > >> ________________________________ > >> From: marc abel <[email protected]> > >> To: pra pa <[email protected]> > >> Cc: [email protected]; [email protected] > >> Sent: Tue, November 3, 2009 9:32:10 PM > >> Subject: Re: [OSL | CCIE_RS] Comitted access rate > >> > >> I aggree that you should use the MQC but you also need to look at > >> shaping instead of policing. Something like > >> > >> policy MYPOLICY > >> class class-default > >> shape average 2000000 125000 125000 > >> > >> int fa0/0 > >> service-policy MYPOLICY out > >> > >> On Tue, Nov 3, 2009 at 2:08 PM, pra pa <[email protected]> wrote: > >>> use MQC > >>> > >>> ________________________________ > >>> Date: Tue, 3 Nov 2009 11:59:56 -0800 > >>> From: [email protected] > >>> To: [email protected] > >>> Subject: [OSL | CCIE_RS] Comitted access rate > >>> > >>> I have an Ethernet LAN connected to my router and i want to rate limit > >>> the > >>> bandwith of the LAN users to 02 Mbps. > >>> > >>> I apply the command rate-limit input 2000000 125000 125000 conform > >>> transmit > >>> exceed drop and i noticed that there is a lot of dropped packets. I > also > >>> applied it on the out side. > >>> > >>> I try to change the Bc and Be several times and packets are still > >>> dropped. > >>> I > >>> want to shape the exceeding traffic at the CIR and not dropping it. > >>> > >>> Can somebody help ? > >>> > >>> I also want to make sure that the default Tc for and Ethernet interface > >>> is > >>> 125 ms. I dont know how to check it. > >>> > >>> Thanks ! > >>> > >>> ________________________________ > >>> From: Syed Zaidi <[email protected]> > >>> To: [email protected] > >>> Sent: Tue, November 3, 2009 7:54:13 PM > >>> Subject: [OSL | CCIE_RS] Calculating lowest MAC Address > >>> > >>> I would like to know if we can derive the lowest MAC address in the > below > >>> mentioned way , I mean, of course with a windows scientific calculator. > >>> bridge ID: 0019.069c.80e0 -> converting it into decimal gives us -> > >>> 107485102304 > >>> bridge ID: 000a.8a4b.a400 -> converting it into decimal gives us -> > >>> 45269885952 -> This one is has the lower MAC address value. > >>> Regards, > >>> Syed > >>> __________________________________________________ > >>> Do You Yahoo!? > >>> Tired of spam? Yahoo! Mail has the best spam protection around > >>> http://mail.yahoo.com > >>> ________________________________ > >>> Find the right PC with Windows 7 and Windows Live. Learn more. > >>> _______________________________________________ > >>> For more information regarding industry leading CCIE Lab training, > please > >>> visit www.ipexpert.com > >>> > >>> > >> > >> > > > > __________________________________________________ > > Do You Yahoo!? > > Tired of spam? Yahoo! Mail has the best spam protection around > > http://mail.yahoo.com > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > -- Regards, Joe Astorino CCIE #24347 (R&S) Sr. Technical Instructor - IPexpert Mailto: [email protected] Telephone: +1.810.326.1444 Live Assistance, Please visit: www.ipexpert.com/chat eFax: +1.810.454.0130 IPexpert is a premier provider of Classroom and Self-Study Cisco CCNA (R&S, Voice & Security), CCNP, CCVP, CCSP and CCIE (R&S, Voice, Security & Service Provider) Certification Training with locations throughout the United States, Europe and Australia. Be sure to check out our online communities at www.ipexpert.com/communities and our public website at www.ipexpert.com
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
