VOIP device - The PC will connect to the phone
On Mon, Mar 7, 2011 at 12:23 PM, khaled Saholy <[email protected]>wrote: > > What will be the connected device at the end ? > > Khaled > > > > Date: Mon, 7 Mar 2011 10:03:46 -0500 > > From: [email protected] > > To: [email protected] > > CC: [email protected]; [email protected] > > > Subject: Re: [OSL | CCIE_RS] Multiple Vlan configure on a port........ > > > > As every one has mentioned "Trunk" the only other thing I can think that > you > > may be trying to get out of us is voice vlan (This is essentially a trunk > > port but I believe Cisco calls is an auxiliary port and suggest that it > is > > more secure than a full out trunk port) > > > > switchport access vlan 20 > > switchport voice vlan 30 > > > > > > On Mon, Mar 7, 2011 at 8:59 AM, Thomas Raabo - Zitcom A/S <[email protected] > >wrote: > > > > > Trunking...dot1q > > > > > > > > > Med venlig hilsen | Best regards > > > Thomas Raabo > > > Netværks ansvarlig > > > > > > > > > > > > _____________________________________________ > > > [email protected] | Direkte: +45 69 10 60 18 | Tlf.: +45 70 23 55 66 > > > > > > > > > -----Original Message----- > > > From: [email protected] [mailto: > > > [email protected]] On Behalf Of Vinod singh Bisht > > > Sent: 7. marts 2011 13:09 > > > To: venkat > > > Cc: [email protected] > > > Subject: Re: [OSL | CCIE_RS] Multiple Vlan configure on a port........ > > > > > > dear venkat > > > > > > is it possible to have one switchport in multiple vlans. > > > > > > if it is, then please give the way by which i can do this. > > > > > > > > > > > > Regards > > > Vinod Singh Bist > > > > > > On Mon, Mar 7, 2011 at 5:24 PM, venkat <[email protected]> wrote: > > > > > > > The last command over writes.. so if you do "show int fa0/24", you > > > > will see only vlan 153. > > > > > > > > -Venkat > > > > > > > > On Mon, Mar 7, 2011 at 3:43 PM, Vinod singh Bisht < > [email protected] > > > >wrote: > > > > > > > >> Hi Guys, > > > >> > > > >> Can I configure multiple VLan on a switch port ? > > > >> > > > >> Ex: > > > >> > > > >> Sw1# config t > > > >> Sw1(config )# int f0/24 > > > >> Sw1(config-if )#switchport access vlan 150 Sw1(config-if > > > >> )#switchport access vlan 151 Sw1(config-if )#switchport access vlan > > > >> 152 Sw1(config-if )#switchport access vlan 153 Sw1(config-if )#do > > > >> wr... > > > >> > > > >> is it possible or it will work or not . I have try it on switch 2950 > > > >> cisco switch but I have configured only a vlan on a switch port > f0/24. > > > >> > > > >> If you have solution then plz suggest me how is it possible with > > > example? > > > >> > > > >> > > > >> > > > >> > > > >> -- > > > >> VINOD SINGH BIST > > > >> > > > >> _______________________________________________ > > > >> For more information regarding industry leading CCIE Lab training, > > > >> please visit www.ipexpert.com > > > >> > > > > > > > > > > > > > > > > > -- > > > VINOD SINGH BIST > > > _______________________________________________ > > > For more information regarding industry leading CCIE Lab training, > please > > > visit www.ipexpert.com > > > _______________________________________________ > > > For more information regarding industry leading CCIE Lab training, > please > > > visit www.ipexpert.com > > > > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
