I made simiilar type topo working without VTP enabled.
2012/1/23 Donald Robb <[email protected]> > I played around with it for a bit and found there is no way for this design > to work. > > > > The switch modules are conflicting with the router and won't even talk to > the other switchports on the same router. > > > > Neat idea though > > > > Cheers, > > Donald Robb > > Productive Networks / Network Consultant > > ______________________________________________________________ > > CCIE Written, CCIP, CCSP, CCDP, CCNP, CCNA: Voice, JNCIP, SCP, MCSA 2003, > Security+, CCSE.R65, PACE > > Experts-Exchange: Guru - R&S > > > > From: Ιωαννης ----------- [mailto:[email protected]] > Sent: January-23-12 12:53 PM > To: [email protected] > Subject: RE: [OSL | CCIE_RS] dynamics > > > > Basically everything looks ok and here is the relevant output ... > > R5 > ------------ > interface FastEthernet0/0 > ip address 150.100.220.5 255.255.255.0 > speed 100 > full-duplex > > CAT 1 > --------------------- > CAT1#show cdp nei > Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge > S - Switch, H - Host, I - IGMP, r - Repeater > Device ID Local Intrfce Holdtme Capability Platform Port ID > R1 Fas 1/1 138 R S I 3725 Fas 0/0 > CAT2 Fas 2/13 130 R S I 3725 Fas 2/13 > R5 Fas 1/5 158 R S I 3725 Fas 0/0 > > interface FastEthernet1/5 > switchport access vlan 567 > duplex full > speed 100 > > interface FastEthernet2/13 > switchport mode trunk > duplex full > speed 100 > ! > > CAT1#show vtp sta > VTP Version : 2 > Configuration Revision : 0 > Maximum VLANs supported locally : 36 > Number of existing VLANs : 6 > VTP Operating Mode : Transparent > VTP Domain Name : ipexpert > VTP Pruning Mode : Disabled > VTP V2 Mode : Disabled > VTP Traps Generation : Disabled > MD5 digest : 0x68 0xB7 0x3C 0x37 0xB2 0x5F 0x37 0x41 > Configuration last modified by 0.0.0.0 at 3-1-02 00:13:05 > > CAT1#show inter trun > Port Mode Encapsulation Status Native vlan > Fa2/13 on 802.1q trunking 1 > Port Vlans allowed on trunk > Fa2/13 1-4094 > Port Vlans allowed and active in management domain > Fa2/13 1,567 > Port Vlans in spanning tree forwarding state and not pruned > Fa2/13 1,567 > CAT1#show vlan-swi brief > VLAN Name Status Ports > ---- -------------------------------- --------- > ------------------------------- > 1 default active Fa1/2, Fa1/3, Fa1/4, Fa1/6 > Fa1/7, Fa1/8, Fa1/9, Fa1/10 > Fa1/11, Fa1/12, Fa1/13, > Fa1/14 > Fa1/15, Fa2/0, Fa2/1, Fa2/2 > Fa2/3, Fa2/4, Fa2/5, Fa2/6 > Fa2/7, Fa2/8, Fa2/9, Fa2/10 > Fa2/11, Fa2/12, Fa2/14, > Fa2/15 > 567 VLAN0567 active Fa1/5 > 1002 fddi-default act/unsup > 1003 token-ring-default act/unsup > 1004 fddinet-default act/unsup > 1005 trnet-default act/unsup > > > CAT 2 > ----------------- > CAT2#show cdp nei > Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge > S - Switch, H - Host, I - IGMP, r - Repeater > Device ID Local Intrfce Holdtme Capability Platform Port ID > R6 Fas 1/6 177 R S I 3725 Fas 0/0 > CAT1 Fas 2/13 167 R S I 3725 Fas 2/13 > > interface FastEthernet1/6 > switchport access vlan 567 > duplex full > speed 100 > > CAT2#show inter trun > Port Mode Encapsulation Status Native vlan > Fa2/13 on 802.1q trunking 1 > Port Vlans allowed on trunk > Fa2/13 1-4094 > Port Vlans allowed and active in management domain > Fa2/13 1,567 > Port Vlans in spanning tree forwarding state and not pruned > Fa2/13 1,567 > CAT2#show vtp sta > VTP Version : 2 > Configuration Revision : 0 > Maximum VLANs supported locally : 36 > Number of existing VLANs : 6 > VTP Operating Mode : Transparent > VTP Domain Name : ipexpert > VTP Pruning Mode : Disabled > VTP V2 Mode : Disabled > VTP Traps Generation : Disabled > MD5 digest : 0x68 0xB7 0x3C 0x37 0xB2 0x5F 0x37 0x41 > Configuration last modified by 0.0.0.0 at 3-1-02 00:02:35 > > CAT2# show vlan-sw brief > VLAN Name Status Ports > ---- -------------------------------- --------- > ------------------------------- > 1 default active Fa1/0, Fa1/1, Fa1/2, Fa1/3 > Fa1/4, Fa1/5, Fa1/8, Fa1/9 > Fa1/10, Fa1/11, Fa1/12, > Fa1/13 > Fa1/14, Fa1/15, Fa2/0, Fa2/1 > Fa2/2, Fa2/3, Fa2/4, Fa2/5 > Fa2/6, Fa2/7, Fa2/8, Fa2/9 > Fa2/10, Fa2/11, Fa2/12, > Fa2/14 > Fa2/15 > 567 VLAN0567 active Fa1/6, Fa1/7 > 1002 fddi-default act/unsup > 1003 token-ring-default act/unsup > 1004 fddinet-default act/unsup > 1005 trnet-default act/unsup > > > R6 > interface FastEthernet0/0 > ip address 150.100.220.6 255.255.255.0 > speed 100 > full-duplex > > R6#ping 150.100.220.5 > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 150.100.220.5, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5) > > > > From: [email protected] > > To: [email protected]; [email protected]; > [email protected] > > Subject: RE: [OSL | CCIE_RS] dynamics > > Date: Mon, 23 Jan 2012 12:02:54 -0700 > > > > What happens exactly? Does it take the trunk command on both ports and > > doesn't trunk? Or you get a command error? > > How is dynamips configured? > > > > Cheers, > > Donald Robb > > Productive Networks / Network Consultant > > ______________________________________________________________ > > CCIE Written, CCIP, CCSP, CCDP, CCNP, CCNA: Voice, JNCIP, SCP, MCSA 2003, > > Security+, CCSE.R65, PACE > > Experts-Exchange: Guru - R&S > > > > -----Original Message----- > > From: [email protected] > > [mailto:[email protected]] On Behalf Of Di Bias, Steve > > Sent: January-23-12 10:17 AM > > To: Ιωαννης -----------; [email protected] > > Subject: Re: [OSL | CCIE_RS] dynamics > > > > Can you post your configs? > > > > Steve Di Bias > > CCIE #32840 > > > > Ιωαννης ----------- <[email protected]> wrote: > > > > > > Hi there, > > I am having a problem with dynamics. Specifically I am not able to trunk > > between two swithes (3725). Although the link shows as a trunk(dot1q > > hardcoded) and I am able to assign ports to the correct VLANS I am not > able > > to ping from one router to another across the two switches (vlans are > going > > across according to the output). Any ideas guys? > > Thanks very much > > Yiannis > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > > visit www.ipexpert.com > > > > Are you a CCNP or CCIE and looking for a job? Check out > > www.PlatinumPlacement.com > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > > > > UHS Confidentiality Notice: This e-mail message, including any > attachments, > > is for the sole use of the intended recipient (s) and may contain > > confidential and privileged information. Any unauthorized review, use, > > disclosure or distribution of this information is prohibited. If this was > > sent to you in error, please notify the sender by reply e-mail and > destroy > > all copies of the original message. > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > > visit www.ipexpert.com > > > > Are you a CCNP or CCIE and looking for a job? Check out > > www.PlatinumPlacement.com > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
