Thanks Kingsley. Here is the config:
R5: ! interface Loopback5 ip address 10.55.55.55 255.255.255.255 ip nat inside ip virtual-reassembly ! ! interface Serial0/1/0 description IPEXPERT uses this interface for CENTRAL segment for YB Practice Lab 1 ip address 192.168.65.5 255.255.255.0 ip nat outside ip virtual-reassembly encapsulation frame-relay ip ospf network point-to-point frame-relay map ip 192.168.65.6 506 broadcast no frame-relay inverse-arp crypto map lmap ! interface Serial0/2/0 description DTE side - Link to R3 DCE s0/2/0 ip address 192.168.35.5 255.255.255.0 ip nat outside ip virtual-reassembly encapsulation ppp ip ospf network point-to-point no fair-queue crypto map lmap ! ip nat inside source route-map s1 interface Serial0/1/0 overload ip nat inside source route-map s2 interface Serial0/2/0 overload ! access-list 102 permit ip host 10.55.55.55 any ! route-map s2 permit 10 match ip address 102 set interface Serial0/2/0 ! route-map s1 permit 10 match ip address 102 set interface Serial0/1/0 ! end Best Regards. ______________________ Adil On Jun 23, 2011, at 12:59 AM, Kingsley Charles wrote: > Configuration please..... > > On Wed, Jun 22, 2011 at 9:57 PM, Adil Pasha <[email protected]> wrote: > Hi guys, > > This is about NAT question. > > For some reason I am not seeing the correct NAT'd address when I PING from R3 > to R5 even though the ICMP is being sent from 192.168.35.3 to R5 and R5 > replies with NAT'd address as you can see on R3' debug. > > R3# > *Jun 22 16:25:48.462: ICMP: echo reply rcvd, src 192.168.65.5, dst > 192.168.35.3 > *Jun 22 16:25:48.462: ICMP: echo reply rcvd, src 192.168.65.5, dst > 192.168.35.3 > *Jun 22 16:25:48.466: ICMP: echo reply rcvd, src 192.168.65.5, dst > 192.168.35.3 > *Jun 22 16:25:48.470: ICMP: echo reply rcvd, src 192.168.65.5, dst > 192.168.35.3 > *Jun 22 16:25:48.474: ICMP: echo reply rcvd, src 192.168.65.5, dst > 192.168.35.3 > R3# > > R5# > Jun 22 18:39:26.547: ICMP: echo reply sent, src 10.55.55.55, dst 192.168.35.3 > Jun 22 18:39:26.551: ICMP: echo reply sent, src 10.55.55.55, dst 192.168.35.3 > Jun 22 18:39:26.555: ICMP: echo reply sent, src 10.55.55.55, dst 192.168.35.3 > Jun 22 18:39:26.559: ICMP: echo reply sent, src 10.55.55.55, dst 192.168.35.3 > Jun 22 18:39:26.559: ICMP: echo reply sent, src 10.55.55.55, dst 192.168.35.3 > R5#sh ip nat tran > > When I check the NAT it is not 192.168..35.5. Could it be a bug or my error? > > R5#sh ip nat translations > Pro Inside global Inside local Outside local Outside global > icmp 192.168.65.5:3 10.55.55.55:3 192.168.35.3:3 192.168.35.3:3 > R5# > > > Best Regards. > ______________________ > Adil > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
