Hm... Never used it before but it seemed to accept it, thanks, pal. What about "rx" and "both" ? And one more thing. I don't have any preference whether to use IDM or IME but still want to be fully prepared. The blueprint says it is going to be and IDM and Marta previously mentioned that IME is an application to manage the IPS.
From: Mike Rojas [mailto:[email protected]] Sent: Sunday, July 08, 2012 5:42 PM To: Eugene Pefti; [email protected] Cc: [email protected] Subject: RE: [OSL | CCIE_Security] Switches in the lab It always does that, set it up as "replicate" Mike > From: [email protected]<mailto:[email protected]> > To: [email protected]<mailto:[email protected]> > Date: Mon, 9 Jul 2012 00:38:19 +0000 > CC: > [email protected]<mailto:[email protected]> > Subject: Re: [OSL | CCIE_Security] Switches in the lab > > Thanks, Matt and sorry for being lazy and not looking into the blueprint ;) > Since we touched SPAN sessions to be setup on the switch a quick question, > maybe two. > 1) If we configure the source interface/vlan do we have to explicitly set it > to "both" or having "rx" is enough. > 2) I'm configuring the physical interface on the switch as the destination, > i.e. > > SW2(config)#monitor session 1 dest int Fa0/10 encap dot1q > % Warning: One or more specified dest port does not support requested > encapsulation. > > Why does the switch warns me about this? I have my Fa0/10 setup as dot1q > trunk. > > Eugene > > > -----Original Message----- > From: Matt Hill [mailto:[email protected]] > Sent: Sunday, July 08, 2012 5:23 PM > To: Eugene Pefti > Cc: > [email protected]<mailto:[email protected]> > Subject: Re: [OSL | CCIE_Security] Switches in the lab > > From the blueprint - which I just happened to have opened :) > > Cisco 3800 Series Integrated Services Routers (ISR) * Cisco 1800 Series > Integrated Services Routers (ISR) * Cisco Catalyst 3560 Series Switches * > Cisco ASA 5500 Series Adaptive Security Appliances * Cisco IPS Series 4200 > Intrusion Prevention System sensors * Cisco Secure Access Control Server for > Windows > Note: > The IPS sensor can be configured using CLI and managed through the IPS Device > Manager. > Software Versions > * Cisco ISR Series running IOS Software Version 12.4T Advanced Enterprise > Services feature set is used on all routers * Cisco Catalyst 3560 Series > Switches running Cisco IOS Software Release 12.2(44)SE or above * Cisco ASA > 5500 Series Adaptive Security Appliances OS Software Version 8.x * Cisco IPS > Software Release 6.1.x * Cisco VPN Client Software for Windows, Release 5.x * > Cisco Secure ACS for Windows Version 4.1 > > So go for it with the 3560s. 3750 is pretty much the same beast. > > Cheers, > Matt > > CCIE #22386 > CCSI #31207 > > On 9 July 2012 10:16, Eugene Pefti > <[email protected]<mailto:[email protected]>> wrote: > > Can you guys confirm that we will have 3560/3750 switches in the lab > > and not 3550. I just hate to remember that we need a reflector port to > > setup a SPAN session on 3550 switch > > > > > > > > Eugene > > > > > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, > > please visit www.ipexpert.com<http://www.ipexpert.com> > > > > Are you a CCNP or CCIE and looking for a job? Check out > > www.PlatinumPlacement.com<http://www.PlatinumPlacement.com> > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com<http://www.ipexpert.com> > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com<http://www.PlatinumPlacement.com>
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
