You have no dialplan-pattern under telephony service or voice translation-rules?
________________________________ From: jeremy co [mailto:[EMAIL PROTECTED] Sent: Saturday, November 15, 2008 12:24 AM To: Hardesty, Scott Cc: Greg Miglucci (gmiglucc); CCIE Voice Maillist Subject: Re: [OSL | CCIE_Voice] CUE Wired problem: call to voice pilotnumberworks, but message button not working. Hi, I added that, but I ran transcoder for other purposes, I don't think that it is related to voice mail. Any way, wired thing is when I press message button I can see it dialed pilot number and then connected ,but I cannot hear anything. However, when I call 4444 , every thing is fine. Jeremy On Sat, Nov 15, 2008 at 4:06 PM, Hardesty, Scott <[EMAIL PROTECTED]> wrote: I do not see your XCODER defined in CME. Try adding sdspfarm tag 1 XCODER under Telephony-service. Scott Hardesty | Cisco Engineer | MidAtlantic | Presidio Networked Solutions 7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | [EMAIL PROTECTED] D: 301.313.2041 | C: 443.789.1219 | www.presidio.com <http://www.presidio.com/> ________________________________ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of jeremy co Sent: Saturday, November 15, 2008 12:00 AM To: Greg Miglucci (gmiglucc) Cc: CCIE Voice Maillist Subject: Re: [OSL | CCIE_Voice] CUE Wired problem: call to voice pilotnumberworks, but message button not working. Hi, I forgot to mention that when I press message button , call connects to voice pilot number but I cannot hear anything Here is the config: ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 ! ! ! ! ! mgcp ! sccp local FastEthernet0/0.200 sccp ccm 200.0.0.254 identifier 1 sccp ! sccp ccm group 1 associate ccm 1 priority 1 associate profile 1 register XCODER ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 4 associate application SCCP ! ! dial-peer voice 5000 pots destination-pattern 0982133335... direct-inward-dial forward-digits 8 ! dial-peer voice 4000 pots destination-pattern 061388884... direct-inward-dial forward-digits 4 ! dial-peer voice 30 pots destination-pattern 01124344... port 1/2:0 forward-digits 8 ! dial-peer voice 200 pots incoming called-number . direct-inward-dial port 1/2:0 ! dial-peer voice 600 voip destination-pattern 2222 session target ras dtmf-relay h245-alphanumeric ! dial-peer voice 999 voip destination-pattern 4444 session protocol sipv2 session target ipv4:200.0.0.100 dtmf-relay sip-notify codec g711ulaw no vad ! dial-peer voice 1001 voip destination-pattern 7000 session protocol sipv2 session target ipv4:200.0.0.100 dtmf-relay sip-notify codec g711ulaw no vad ! dial-peer voice 7878 voip destination-pattern 800[01].... session protocol sipv2 session target ipv4:114.0.0.0.254 dtmf-relay sip-notify codec g711ulaw no vad ! gateway timer receive-rtp 1200 ! sip-ua ! ! ! ! gatekeeper zone local FXSZONE abc.com 7.7.7.7 invia IPIPGWZONE outvia IPIPGWZONE enable-intrazone zone local CCMZONE abc.com zone local HQZONE abc.com zone local IPIPGWCCMZONE abc.com zone local IPIPGWZONE abc.com zone prefix HQZONE 011* zone prefix IPIPGWCCMZONE 3... gw-type-prefix 1#* default-technology no use-proxy FXSZONE default inbound-to terminal no use-proxy FXSZONE default outbound-from terminal bandwidth interzone zone CCMZONE 144 no shutdown ! ! telephony-service max-ephones 10 max-dn 200 ip source-address 200.0.0.254 port 2000 sdspfarm units 1 sdspfarm transcode sessions 2 create cnf-files version-stamp 7960 Mar 02 2002 04:09:38 voicemail 4444 mwi relay max-conferences 4 gain -6 web admin system name admin secret 5 $1$fS6t$7Pfc17AMenIo5ISKL3w2N0 ! ! ephone-dn 38 number 1000 ! ! ephone-dn 70 number 9911 call-forward noan 4444 timeout 10 ! ! ephone-dn 80 number 8000.... mwi on ! ! ephone-dn 81 number 8001.... mwi off ! ! ephone 1 username "pstn" password cisco mac-address 0030.94C2.BFB1 button 1:70 ! Jeremy On Sat, Nov 15, 2008 at 3:40 PM, Greg Miglucci (gmiglucc) <[EMAIL PROTECTED]> wrote: Post your telephony-service config and ephone-dn and dial-peer config. Also are you using dial-plan pattern under teleph-service? If so you need to make sure you have appropriate translation-rules. ________________________________ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of jeremy co Sent: Friday, November 14, 2008 11:28 PM To: CCIE Voice Maillist Subject: Re: [OSL | CCIE_Voice] CUE Wired problem: call to voice pilotnumber works, but message button not working. I forgot to mention that when I press message button , call even connected to voice pilot number but I cannot hear anything Jeremy On Sat, Nov 15, 2008 at 3:12 PM, jeremy co <[EMAIL PROTECTED]> wrote: Hi, When I call to voice pilot number, it works, but when hit message button it wouldn't work. Can someone shed light on what may cause this issue? I restarted cue and phones but it's not working. Jeremy
