Hi Tamer, Thanks for the link, but it just stated that it doesn't work without any further explanation. In fact there is a workaround to resolve this by Cisco, pls refer below:
*CSCti11843 Bug Details:* Shared-line Cbarge remote-in-use softkeys not working in SRST Symptom: For Shared line if you want cbarge you must disable privacy and enable remote-in-use softkey under ephone-template. However if you configured SRST CME with srst mode auto-provision none or dn privacy setting on the ephone remains default which means it is on. Hence you can’t disable privacy. *Conditions:* When phones fallback to SRST. *Workaround:* Only workaround is to either configure: ephone 1 privacy off or configure srst mode auto-provision all And yes, i just make it work few min ago. Just that the behavior is odd. Shingei. On Fri, Feb 25, 2011 at 10:22 PM, Tamer Ismail <[email protected]> wrote: > Check following post: > > http://www.voiceie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=8;t=002799 > > it’s saying that cbarge and sharde line privacy are supported only in > cme/srst 7.1 not owr version 7.0 > > > > Best regards, > > Tamer Ismail > > > > *From:* ShinGei Yong [mailto:[email protected]] > *Sent:* Friday, February 25, 2011 4:03 PM > *To:* Tamer Ismail; [email protected] > *Subject:* Re: [OSL | CCIE_Voice] cBarge in SRST:cbarge softkey not > appearing > > > > Hi Tamer, > > Are you sure cBarge is not possible for SRST? > I believe this topic has been posted several times since-ever, just that > circumstance varies. > > http://ccieash.wordpress.com/2010/06/21/hardware-conferencing-ios/ > > Shingei. > > On Fri, Feb 25, 2011 at 9:39 PM, Tamer Ismail <[email protected]> wrote: > > As far as I know, we can’t achieve cbarge in SRST. > > > > Best regards, > > Tamer Ismail > > > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *ShinGei Yong > *Sent:* Friday, February 25, 2011 1:33 PM > *To:* [email protected] > *Subject:* [OSL | CCIE_Voice] cBarge in SRST:cbarge softkey not appearing > > > > Hi, > > I'm trying the cbarge during SRST. I've privacy turn off on my two 7961 > ipphone, > and has assigned a ephone template with softkeys remote-in-use cbarge > newcall. > > Somehow when SRST,the softkeys "cbarge"doesn't appear on the phone when the > shared line was answered by another ipphone with the same DN > configured.I've check > the below items: > > 1. Both ipphones have privacy turn off > ephone-2[1] Mac:001E.F728.2C0C TCP socket:[2] activeLine:0 REGISTERED in > SCCP ver 17/9 > mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 > caps:8 privacy:0 > IP:10.10.202.55 43050 7961 keepalive 6 max_line 5 available_line 3 > button 1: dn 1 number 3001 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE > button 2: dn 2 number 3080 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE shared > Preferred Codec: g711ulaw > > > ephone-3[2] Mac:0019.E8AE.9479 TCP socket:[5] activeLine:0 REGISTERED in > SCCP ver 17/9 > mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 > caps:8 privacy:0 > IP:10.10.202.53 38999 7961 keepalive 0 max_line 5 available_line 3 > button 1: dn 3 number 3002 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE > button 2: dn 4 number 1010 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE > button 3: dn 2 number 3080 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE shared > Preferred Codec: g711ulaw > > 2. Conference resources is registered with CME SRST. > BR2-RTR(config)#do sh sdspfar uni regi > > conf-1 Device:br2-cfb TCP socket:[4] REGISTERED in SCCP ver 17/10 > actual_stream:8 max_stream 8 IP:10.10.202.1 14335 Conference Dixieland > keepalive 3 > Supported codec: > G711Ulaw > G711Alaw > G729 > G729a > G729b > G729ab > > 3. Correct ephone-template assigned > > ephone-template 1 > softkeys remote-in-use CBarge Newcall > softkeys idle Newcall Redial Cfwdall > > 4. Ad-hoc conference configured > ephone-dn 10 octo-line > number A001 > conference ad-hoc > preference 5 > > 5. Telephony-service Setting > telephony-service > sdspfarm units 2 > sdspfarm tag 1 br2-cfb > sdspfarm tag 2 br2-xcoder > conference hardware > srst mode auto-provision none > srst ephone template 1 > srst dn template 1 > srst dn line-mode dual-octo > max-ephones 5 > max-dn 10 preference 5 no-reg primary > ip source-address 10.10.202.1 port 2000 > system message CCIE Voice Test > time-zone 28 > date-format dd-mm-yy > voicemail 3600 > max-conferences 4 gain -6 > moh music-on-hold.au > multicast moh 239.1.1.1 port 16384 route 10.10.110.3 10.10.202.1 > transfer-system full-consult > secondary-dialtone 0 > > Both phones and router have been reset N time,but the cbarge still doesn't > appear. > > Did i miss out anything? > > TIA > Shingei > > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
