Hi Ruben, Though last build label in the Webdashboard is getting updated with proper label name, label is not getting applied to the checked in files. Can you please help me with this?
I added the following lines to the config file. <labeller type="fileLabeller"> <labelFilePath>C:\label.txt</labelFilePath> </labeller> C:\>type label.txt NIGHTLY_MAIN_BUILD Thanks Saran On Oct 6, 1:53 pm, Saran <[EMAIL PROTECTED]> wrote: > Thanks very much Ruben and Bolek for your valuable suggestions, I will > update this post again with my experience. > Saran > > On Oct 5, 6:00 am, tboloo <[EMAIL PROTECTED]> wrote: > > > Hi > > Here's what I do to have labels in ClearCase: > > > In my project configuration block I have a labeller block with > > following contents: > > > <labeller type="defaultlabeller"> > > <prefix>BUILD_OK_</prefix> > > </labeller> > > > and then I have label in format <prefix><number_of_build> applied to > > source. > > Works most of the time, although I run into issue when CC.NET tried to > > apply the same label (with the same number), and I got exception. I > > haven't investigated it, just manually removed offending label from > > ClearCase. > > > Hope this helps, > > > Regads, > > Bolek. > > > Ruben Willems napisał(a): > > > > Hi > > > > The file labeler allows you to use the BuildOK label, without any number. > > > so > > > I would try it out. > > > > Now I do not know if your sourcecontrol allows double labels, > > > but I doubt it (it would be silly if it did). > > > I know VSS replaces the build label if you use a dumplicate label > > > If clearcase does the same, than you just need to use this file labeler, > > > if not a setup as below would be a good approach > > > > use the file labeller, pointing to file with a contents of BuildOK > > > set up a task in the task section that will remove the existing BuildOK > > > rom clearcase > > > a batch file or so that will be ran with the exec task in ccnet. > > > set this task as the LAST task n the task section > > > > The reason : : the operation flow of ccnet is as follows : > > > > 1) Wait for the triggers to awaken. > > > 2) Ask the source control system for a list of the modifications > > > since the last build. > > > 3) If any modifications were found or if the triggers said "force > > > the > > > build": > > > 3.1) Generate a label for the build. > > > 3.2) Run the prebuild tasks in the order specified, failing > > > the build in case of error. > > > 3.3) Get the source code from the source control system. > > > 3.4) Run the build tasks in the order specified, failing > > > the > > > build in case of error. > > > 3.5) If the repository should be labeled: > > > 3.5.1) Let the source control system apply the > > > label. > > > 3.6) Run the publisher tasks. > > > 4) Go to 1. > > > > This should have the desired result > > > > with kind regards > > > Ruben Wilems > > > > On Fri, Oct 3, 2008 at 10:17 PM, Saran <[EMAIL PROTECTED]> wrote: > > > > > Hi Ruben, > > > > > I would like to keep moving the BUILDOK label whenever there is a > > > > successful build to all the files that were checked in after previous > > > > successful build. Our plan is to let developers use this label for > > > > view update, this will make sure that whenever they update the view it > > > > will be in buildable state. > > > > > Thanks very much for your time > > > > Saran > > > > > ps: I looked in to the filelabeler and I think this will not address > > > > my requirements, please correct me if I'm wrong. > > > > > On Oct 3, 3:01 pm, "Ruben Willems" <[EMAIL PROTECTED]> wrote: > > > > > Hi > > > > > > just thought of something : > > > > > maybe you can take a look at the file labeler : > > > >http://confluence.public.thoughtworks.org/display/CCNET/File+Labeller > > > > > This sounds like the solution to your problem. > > > > > > with kind regards > > > > > Ruben Willems > > > > > > On Fri, Oct 3, 2008 at 4:18 PM, Saran <[EMAIL PROTECTED]> wrote: > > > > > > > Thanks Reben, but I guess I cannot apply customized label > > > > > > (LAST_SUCCESS_LABEL) using Cruisecontrol.net. > > > > > > Saran > > > > > > > On Oct 3, 6:28 am, "Ruben Willems" <[EMAIL PROTECTED]> wrote: > > > > > > > Hi > > > > > > > > In default the defaultLabeler is use > > > > > > > (if you do not specify a labeler section in your ccnet.config, you > > > > get > > > > > > this > > > > > > > one) > > > > >http://confluence.public.thoughtworks.org/display/CCNET/Default+Labeller > > > > > > > > When you have set useLabel to true, a label will be applied. > > > > > > > The layout of this label is will be the buildnumber. > > > > > > > You can add a prefix to it (BuildOk-), so the label will be > > > > > > > BuilOK-25 > > > > > > > > with kind regards > > > > > > > Ruben Willems > > > > > > > > On Fri, Sep 26, 2008 at 4:19 PM, Saran <[EMAIL PROTECTED]> wrote: > > > > > > > > > Hi, > > > > > > > > > I would like to apply build label (BUILD_OK) if build succeeds > > > > > > > > but > > > > I'm > > > > > > > > not sure how to specify build label name to cruisecontrol.net. > > > > > > > > In > > > > the > > > > > > > > source control block, there is an option to apply label > > > > > > > > (useLabel), > > > > > > > > but I can't figure out how to specify the build label name. > > > > > > > > > <sourcecontrol type="clearCase"> > > > > > > > > <viewPath>C:\PATH\TO\SOURCE</viewPath> > > > > > > > > <branch>main</branch> > > > > > > > > <autoGetSource>false</autoGetSource> > > > > > > > > <useLabel>true</useLabel> > > > > > > > > <useBaseline>false</useBaseline> > > > > > > > > <projectVobName>PROJECT_VOB_NAME</projectVobName> > > > > > > > > <viewName>PROJECT_VIEW_NAME</viewName> > > > > > > > > <executable>cleartool.exe</executable> > > > > > > > > <timeout>50000</timeout> > > > > > > > > </sourcecontrol> > > > > > > > > > Any suggestions would be really appreciated. > > > > > > > > > Thanks very much, > > > > > > > > Saran
