I can get a stair stepping easily enough on most terminal emulators (this was
Solaris 10 CDE dtterm):
$ stty -onlcr
$
$
$
$ stty sane
$
$
$
So maybe for some reason, it was bringing up the pseudo-terminal with the wrong
tty modes. :-)
> On Nov 24, 2020, at 16:39, Antonis Tsolomitis <[email protected]>
> wrote:
>
>
> You are right. I got confused with Ubuntu in which installation of a service
> enables it and runs it as well.
> In Arch it needs to me explicitly enabled, and I forgot this.
>
> So, everything is fine on Arch and Manjaro the only additional step is to
> install rpcsvc-proto.
>
> On Debian testing I still have to learn why dtterm stair-steps the prompts
> until it is reset.
> (this problem does not appear on Arch).
>
> Thanks for all the help,
>
> Antonis.
>
>
>
> On 11/24/20 6:56 PM, Danilo Pecher wrote:
>> That error means you don't have the rpcbind service running
>>
>> On Tue, 24 Nov 2020 at 17:54, Antonis Tsolomitis
>> <[email protected] <mailto:[email protected]>> wrote:
>>
>>
>> True. So the package
>>
>> rpcsvc-proto
>>
>> needs to be installed on Arch/Manjaro. This information is missing from
>>
>> https://sourceforge.net/p/cdesktopenv/wiki/Archlinux_Build/#install-packages
>> <https://sourceforge.net/p/cdesktopenv/wiki/Archlinux_Build/#install-packages>
>>
>> Can it be added?
>>
>> Now libcsa has been compiled and installed. The problem however persists on
>> Manjaro.
>> ttsession (although build and installed):
>>
>> "The desktop messaging system could not be started"
>> 1. Click OK etc etc
>>
>> On another window:
>> "A ToolTalk connection could not be established.......... no ttsession
>> process is running".
>>
>> These are typical errors for CDE from the past. So what to look for should
>> be known to
>> experts of the CDE code. So, any idea how to debug?
>>
>> Antonis.
>>
>>
>> On 11/24/20 3:25 PM, Danilo Pecher wrote:
>>> If libcsa isn't built, you're most likely missing rpcgen on your system
>>>
>>> On Tue, 24 Nov 2020 at 14:20, Antonis Tsolomitis
>>> <[email protected] <mailto:[email protected]>> wrote:
>>> On 11/24/20 7:57 AM, Peter Howkins wrote:
>>>>
>>>> I've pushed a series of patches to master that should resolve the GCC 10
>>>> build issues. Hopefully that will be enough to get the Fedora build
>>>> working, but I've only tested it on Debian.
>>>>
>>>> Peter
>>>>
>>>> --
>>>> Peter Howkins
>>>> [email protected] <mailto:[email protected]>
>>>> https://www.marutan.net/ <https://www.marutan.net/>
>>>>
>>>
>>>
>>>
>>> Yes it compiles on Debian testing. However there are some problems in
>>> dtterm shown in attached screenshot.
>>> I remember this is an old problem but I forgot its solution. At the
>>> beggining of the screenshot I enabled Return and Line feed
>>> so no stairs get priduced. But then I can not use mv -i as I get the prompt
>>> immediately after the overwrite question.
>>>
>>> On ManjaroLinux/Arch it compiles but libcsa does not get produced.
>>> The make log for Manjaro is located here
>>> https://myria.math.aegean.gr/~atsol/tmp/make.log
>>> <https://myria.math.aegean.gr/~atsol/tmp/make.log>
>>>
>>> Moreover, the desktop does not start on Manjaro/Arch... it complains about
>>> /etc/hosts and the messaging system that does not get started.
>>> I do not know if this is related to libcsa.
>>>
>>> Antonis.
>>> _______________________________________________
>>> cdesktopenv-devel mailing list
>>> [email protected]
>>> <mailto:[email protected]>
>>> https://lists.sourceforge.net/lists/listinfo/cdesktopenv-devel
>>> <https://lists.sourceforge.net/lists/listinfo/cdesktopenv-devel>
>>
>
> _______________________________________________
> cdesktopenv-devel mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/cdesktopenv-devel
_______________________________________________
cdesktopenv-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/cdesktopenv-devel
