Hi,
I think it's likely that this is a known problem, but I haven't been
able to find anything relevant in TFM or on the net.
The problem is that only the first scsi bus is reported by executing
cdrecord -scanbus, which makes it difficult to use cdrecord with
xcdroast when the CD-R is not on the first bus. The machine has an
Adaptec 2940 as scsi0, an Adaptec 2940uw as scsi1 and ide-scsi
emulation for an ATAPI CD-R as scsi2.
I've successfully used cdrecord and xcdroast with this scsi setup in
the past. What's changed? I'd be very appreciative if someone could
point out the solution or give me a clue to things I should be
looking at.
I have cdrecord compiled with debugging so I would be able to provide
additional information from that source if it would help.
Many thanks,
Mike McKernan
These are the vitals on my setup
Linux Mandrake release 7.2 (Odyssey) for i586
Linux tivoli.mv.com 2.4.2 #2 SMP Sun Mar 11 20:19:44 EST 2001
i686 unknown
cdrecord-1.9-6
glibc-2.2.2-4mdk
compat-glibc-7.2-2.1.3.2mdk
This is what I get from cdrecord:
<tivoli: i686-linux-cc> ./cdrecord -scanbus
Cdrecord 1.9 (i686-pc-linux-gnu) Copyright (C) 1995-2000 Jörg Schilling
Linux sg driver version: 3.1.17
Using libscg version 'schily-0.1'
scsibus0:
0,0,0 0) 'HP ' 'C2520A ' '3503' Processor
0,1,0 1) *
0,2,0 2) *
0,3,0 3) *
0,4,0 4) 'HP ' 'C1533A ' '9406' Removable Tape
0,5,0 5) 'SONY ' 'CD-ROM CDU-76S ' '1.2d' Removable CD-ROM
0,6,0 6) 'PIONEER ' 'CD-ROM DRM-600 ' '2404' Removable CD-ROM
0,7,0 7) *
I'll do this again with -V at the end of the message.
However, specifying dev:
<tivoli: i686-linux-cc> ./cdrecord -scanbus dev=2,0,0
Cdrecord 1.9 (i686-pc-linux-gnu) Copyright (C) 1995-2000 Jörg Schilling
scsidev: '2,0,0'
scsibus: 2 target: 0 lun: 0
Linux sg driver version: 3.1.17
Using libscg version 'schily-0.1'
scsibus2:
2,0,0 200) 'MITSUMI ' 'CR-4801TE ' '1.04' Removable CD-ROM
2,1,0 201) *
2,2,0 202) *
2,3,0 203) *
2,4,0 204) *
2,5,0 205) *
2,6,0 206) *
2,7,0 207) *
which is the device of interest. Using -inq for that device gives this:
<tivoli: i686-linux-cc> ./cdrecord -inq dev=2,0,0
Cdrecord 1.9 (i686-pc-linux-gnu) Copyright (C) 1995-2000 Jörg Schilling
scsidev: '2,0,0'
scsibus: 2 target: 0 lun: 0
Linux sg driver version: 3.1.17
Using libscg version 'schily-0.1'
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'MITSUMI '
Identifikation : 'CR-4801TE '
Revision : '1.04'
Device seems to be: Philips CDD-522.
/proc/scsi/scsi
<tivoli: i686-linux-cc> cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: HP Model: C2520A Rev: 3503
Type: Processor ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: HP Model: C1533A Rev: 9406
Type: Sequential-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: SONY Model: CD-ROM CDU-76S Rev: 1.2d
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: PIONEER Model: CD-ROM DRM-600 Rev: 2404
Type: CD-ROM ANSI SCSI revision: 01 CCS
Host: scsi0 Channel: 00 Id: 06 Lun: 01
Vendor: PIONEER Model: CD-ROM DRM-600 Rev: 2404
Type: CD-ROM ANSI SCSI revision: 01 CCS
Host: scsi0 Channel: 00 Id: 06 Lun: 02
Vendor: PIONEER Model: CD-ROM DRM-600 Rev: 2404
Type: CD-ROM ANSI SCSI revision: 01 CCS
Host: scsi0 Channel: 00 Id: 06 Lun: 03
Vendor: PIONEER Model: CD-ROM DRM-600 Rev: 2404
Type: CD-ROM ANSI SCSI revision: 01 CCS
Host: scsi0 Channel: 00 Id: 06 Lun: 04
Vendor: PIONEER Model: CD-ROM DRM-600 Rev: 2404
Type: CD-ROM ANSI SCSI revision: 01 CCS
Host: scsi0 Channel: 00 Id: 06 Lun: 05
Vendor: PIONEER Model: CD-ROM DRM-600 Rev: 2404
Type: CD-ROM ANSI SCSI revision: 01 CCS
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: IBM-PCCO Model: DDRS-39130W !# Rev: S97B
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: COMPAQPC Model: DDRS-39130W Rev: S99C
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 03 Lun: 00
Vendor: IBM-PSG Model: DNES-309170W !# Rev: SAHR
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: MITSUMI Model: CR-4801TE Rev: 1.04
Type: CD-ROM ANSI SCSI revision: 02
Here's the scanbus output with -V:
<tivoli: i686-linux-cc> ./cdrecord -scanbus -V
Cdrecord 1.9 (i686-pc-linux-gnu) Copyright (C) 1995-2000 Jörg Schilling
Linux sg driver version: 3.1.17
Using libscg version 'schily-0.1'
scsibus0:
Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
0,0,0 0)
Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'inquiry' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 12 00 00 00 24 00
cmd finished after 0.001s timeout 40s
Inquiry Data : 03 00 02 02 1F 00 00 00 48 50 20 20 20 20 20 20 43 32 35
32 30 41 20 20 20 20 20 20 20 20 20 20 33 35 30 33
Inquiry Data : ........HP C2520A 3503
'HP ' 'C2520A ' '3503' Processor
Executing 'test unit ready' command on Bus 0 Target 1, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
0,1,0 1) *
Executing 'test unit ready' command on Bus 0 Target 2, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
0,2,0 2) *
Executing 'test unit ready' command on Bus 0 Target 3, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
0,3,0 3) *
Executing 'test unit ready' command on Bus 0 Target 4, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable
error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0E 00 00 00 00 3A 00 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.008s timeout 40s
0,4,0 4)
Executing 'test unit ready' command on Bus 0 Target 4, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable
error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0E 00 00 00 00 3A 00 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.006s timeout 40s
Executing 'inquiry' command on Bus 0 Target 4, Lun 0 timeout 40s
CDB: 12 00 00 00 24 00
cmd finished after 0.003s timeout 40s
Inquiry Data : 01 80 02 02 26 00 00 18 48 50 20 20 20 20 20 20 43 31 35
33 33 41 20 20 20 20 20 20 20 20 20 20 39 34 30 36
Executing 'inquiry' command on Bus 0 Target 4, Lun 0 timeout 40s
CDB: 12 00 00 00 2B 00
cmd finished after 0.003s timeout 40s
Inquiry Data : 01 80 02 02 26 00 00 18 48 50 20 20 20 20 20 20 43 31 35
33 33 41 20 20 20 20 20 20 20 20 20 20 39 34 30 36 20 20 20 39 00 00 02
Inquiry Data : ....&...HP C1533A 9406 9...
'HP ' 'C1533A ' '9406' Removable Tape
Executing 'test unit ready' command on Bus 0 Target 5, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable
error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 00 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 40s
0,5,0 5)
Executing 'test unit ready' command on Bus 0 Target 5, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable
error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 00 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 40s
Executing 'inquiry' command on Bus 0 Target 5, Lun 0 timeout 40s
CDB: 12 00 00 00 24 00
cmd finished after 0.001s timeout 40s
Inquiry Data : 05 80 02 02 1F 00 00 18 53 4F 4E 59 20 20 20 20 43 44 2D
52 4F 4D 20 43 44 55 2D 37 36 53 20 20 31 2E 32 64
Inquiry Data : ........SONY CD-ROM CDU-76S 1.2d
Executing 'mode sense g1' command on Bus 0 Target 5, Lun 0 timeout 40s
CDB: 5A 00 3F 00 00 00 00 00 08 00
./cdrecord: Input/output error. mode sense g1: scsi sendcmd: retryable error
CDB: 5A 00 3F 00 00 00 00 00 08 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 20 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x20 Qual 0x00 (invalid command operation code) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 5, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable
error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 00 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 40s
Executing 'mode sense g0' command on Bus 0 Target 5, Lun 0 timeout 40s
CDB: 1A 00 2A 00 01 00
./cdrecord: Input/output error. mode sense g0: scsi sendcmd: retryable error
CDB: 1A 00 2A 00 01 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 24 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.001s timeout 40s
'SONY ' 'CD-ROM CDU-76S ' '1.2d' Removable CD-ROM
Executing 'test unit ready' command on Bus 0 Target 6, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
0,6,0 6)
Executing 'test unit ready' command on Bus 0 Target 6, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'inquiry' command on Bus 0 Target 6, Lun 0 timeout 40s
CDB: 12 00 00 00 24 00
cmd finished after 0.002s timeout 40s
Inquiry Data : 05 80 01 01 36 00 00 00 50 49 4F 4E 45 45 52 20 43 44 2D
52 4F 4D 20 44 52 4D 2D 36 30 30 20 20 32 34 30 34
Executing 'inquiry' command on Bus 0 Target 6, Lun 0 timeout 40s
CDB: 12 00 00 00 3B 00
cmd finished after 0.003s timeout 40s
Inquiry Data : 05 80 01 01 36 00 00 00 50 49 4F 4E 45 45 52 20 43 44 2D
52 4F 4D 20 44 52 4D 2D 36 30 30 20 20 32 34 30 34 00 00 00 D0 90 27 3E 01 04
91 00 18 06 F0 FC 00 00 07 98 00 00 00 FF
Inquiry Data : ....6...PIONEER CD-ROM DRM-600 2404.....'>................
Executing 'mode sense g1' command on Bus 0 Target 6, Lun 0 timeout 40s
CDB: 5A 00 3F 00 00 00 00 00 08 00
./cdrecord: Input/output error. mode sense g1: scsi sendcmd: retryable error
CDB: 5A 00 3F 00 00 00 00 00 08 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 08 00 00 00 00 20 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x20 Qual 0x00 (invalid command operation code) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 6, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'mode sense g0' command on Bus 0 Target 6, Lun 0 timeout 40s
CDB: 1A 00 2A 00 01 00
./cdrecord: Input/output error. mode sense g0: scsi sendcmd: retryable error
CDB: 1A 00 2A 00 01 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 08 00 00 00 00 24 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 40s
'PIONEER ' 'CD-ROM DRM-600 ' '2404' Removable CD-ROM
Executing 'test unit ready' command on Bus 0 Target 7, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
0,7,0 7) *
Executing 'test unit ready' command on Bus 0 Target 8, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 9, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 10, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 11, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 12, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 13, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 14, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 15, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
./cdrecord: Input/output error. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
