Hi Andy, switching the system off, waiting some hours and trying again, I didn't got the "unsupported MMC" message again. only the speed flag didn't work. Nevertheless I tried again to burn and it burned. Now mediainfo doesn't say "blank" but when I try to mount it failes and "dmesg" gives:
SCSI cdrom error : host 0 channel 0 id 0 lun 0 return code = 28000000 Current sd0b:00: sns = 70 4 ASC=3e ASCQ= 2 Raw sense data:0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3e 0x02 0x00 0x00 0x00 0x00 I/O error: dev 0b:00, sector 0 [..] strange.. any ideas? cu rasca On Sat, 13 Dec 2003 12:07:32 +0100 Rasca <[EMAIL PROTECTED]> wrote: > > I found out that there is a firmware update to version 47 > (original: 40). But after updating I see: > > [EMAIL PROTECTED]:~/pictures> growisofs -speed=1 -Z > /dev/scd0=fotos-backup.iso > :-( /dev/scd0: unsupported MMC profile 10 > [EMAIL PROTECTED]:~/pictures> > > does it mean I have to downgrade my firmware or upgrade my software > (or kernel..)? > > > On Fri, 12 Dec 2003 22:47:17 +0100 > Rasca <[EMAIL PROTECTED]> wrote: > > > > > On Thu, 11 Dec 2003 20:12:27 +0100 > > Andy Polyakov <[EMAIL PROTECTED]> wrote: > > > > > > This was fine. But after burning my first DVD I had a problem. > > > > May be you know the answer. > > > > > > > > My setup: BTC DVD+/-R/RW, Linux kernel 2.4.22, cdrecord 2.x > > > > > > > > Burning was done by > > > > growisofs -Z /dev/scd0=fuji.iso > > > > > > > > No errors or warning were given. But then if I try to > > > > mount it is see: > > > > > > > > attempt to access beyond end of device > > > > 0b:00: rw=0, want=34, limit=2 > > > > isofs_read_super: bread failed, dev=0b:00, iso_blknum=16, block=16 > > > > > > > > dvd+rw-mediainfo gives: > > > > INQUIRY: [DVDRW ][IDE1004 ][0040] > > > > GET [CURRENT] CONFIGURATION: > > > > Mounted Media: 11h, DVD-R Sequential > > > > Media ID: LD01 > > > > Current Write Speed: 4.0x1385=5540KB/s > > > > Write Speed #0: 4.0x1385=5540KB/s > > > > Write Speed #1: 2.0x1385=2770KB/s > > > > Write Speed #2: 1.0x1385=1385KB/s > > > > GET PERFORMANCE: > > > > Speed Descriptor#0: 00/2298496 [EMAIL PROTECTED] [EMAIL PROTECTED] > > > > READ DVD STRUCTURE[#10h]: > > > > Media Book Type: 25h, DVD-R book [revision 5] > > > > Legacy lead-out at: 2298496*2KB=4707319808 > > > > READ DVD STRUCTURE[#0h]: > > > > Media Book Type: 25h, DVD-R book [revision 5] > > > > Last border-out at: 0*2KB=0 > > > > READ DISC INFORMATION: > > > > Disc status: blank > > > > Number of Sessions: 1 > > > > State of Last Session: empty > > > > Number of Tracks: 1 > > > > READ TRACK INFORMATION[#1]: > > > > Track State: blank > > > > Track Start Address: 0*2KB > > > > Next Writable Address: 0*2KB > > > > Free Blocks: 2298496*2KB > > > > Track Size: 2298496*2KB > > > > > > > > A disk status of blank!? strange.. If I have a look > > > > at the surface of the dvd it looks burned.. > > > > > > > > Any ideas? > > > > > > Smells like media poorly supported by your firmware. I mean if surface > > > hue has changed and unit still recognizes media as blank, it sounds like > > > laser power was not enough during recording. You should a) try another > > > media brand, b) try to record at lower speed. As for the latter. Version > > > 5.14 introduces new speed selection code and given the dvd+rw-medainfo > > > output, it might fail. Problem is that units presents several "Write > > > Speed" descriptors, but only one "Performance" descriptor. This means > > > that you might have to use previous version 5.13 at least with this > > > media. I'd like to hear more about your experience with this [preferably > > > on the list]. A. > > > > I went back to 5.13 and used a slower speed. But I failed again: > > > > [EMAIL PROTECTED]:~/pictures> growisofs -Z /dev/scd0=fotos-backup.iso > > -speed=1 > > Executing 'builtin_dd if=fotos-backup.iso of=/dev/scd0 obs=32k seek=0' > > :-[ Failed to change write speed: 2770->1385 > > > > [EMAIL PROTECTED]:~/pictures> growisofs -Z /dev/scd0=fotos-backup.iso > > -speed=2 > > Executing 'builtin_dd if=fotos-backup.iso of=/dev/scd0 obs=32k seek=0' > > /dev/scd0: "Current Write Speed" is 2.0x1385KBps. > > 7864320/1610125312 ( 0.5%) @1.7x, remaining 20:22 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 30:33 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 44:08 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 54:19 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 67:54 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 78:05 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 88:17 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 101:52 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 112:03 > > 7864320/1610125312 ( 0.5%) @0.0x, remaining 125:38 > > :-[ LBA=f00h, SENSE KEY=5h/ASC=21h/ASCQ=02h ] > > :-( write failed: Input/output error > > /dev/scd0: flushing cache > > /dev/scd0: updating RMA > > /dev/scd0: closing session > > [EMAIL PROTECTED]:~/pictures> > > > > and "dmesg" says: > > > > scsi : aborting command due to timeout : pid 37928, scsi0, channel 0, id > > 0, lun 0 0x2a 00 00 00 0f 00 00 00 10 00 > > hdc: irq timeout: status=0xd0 { Busy } > > hdc: ATAPI reset complete > > hdc: irq timeout: status=0xc0 { Busy } > > hdc: ATAPI reset complete > > hdc: irq timeout: status=0xc0 { Busy } > > scsi0 channel 0 : resetting for second half of retries. > > SCSI bus is being reset for host 0 channel 0. > > > > > > > > -- > > Welchen Unterschied macht es f�r die Toten, die Waisen und die > > Heimatlosen, ob irrsinnige Vernichtung im Namen der Diktatur oder im > > heiligen Namen der Freiheit und Demokratie geschieht? - Gandhi - > > > -- > Welchen Unterschied macht es f�r die Toten, die Waisen und die Heimatlosen, > ob irrsinnige Vernichtung im Namen der Diktatur oder im heiligen Namen der > Freiheit und Demokratie geschieht? - Gandhi - -- Welchen Unterschied macht es f�r die Toten, die Waisen und die Heimatlosen, ob irrsinnige Vernichtung im Namen der Diktatur oder im heiligen Namen der Freiheit und Demokratie geschieht? - Gandhi -
