Hi,
This is a message Jim sent some time back and I saved it:
Glenn
The #2 cause of trouble for Baofeng radios is the 2-pin plug is not
fully inserted into the speaker/mic socket of the radio. This is
especially common for radios with the GT-3 style case. There is a
raised ridge around the socket well that contacts the plastic shell of
the 2-pin plug which keeps the pins from being fully inserted. The
work around for this is to trim away the part of the plastic shell
that the ridge of the case is interfering with. This page (scroll down
to the GTE section) has pictures of the problem and they show needs to
be done to eliminate the interference (click on the picture to see a
larger version that is easier to see).
http://www.miklor.com/COM/UV_ErrorMess.php#error1
----- Original Message -----
From: Kheong Sann CHAN
To: Discussion of CHIRP
Sent: Monday, February 17, 2020 7:51 PM
Subject: Re: [chirp_users] chirp connecting to UV-5R from Ubuntu 16.04 on
Lenovo Carbon X1
Aubrey: Thanks for your response. We have some other software on the laptop
that works with 16.04 but seemed to become unstable with Ubuntu 18.04, so I
stuck with 16.04. I will try it later with 20.04 when it comes out.
Glenn: Thanks too for your suggestion. Is there any web-page that gives
instructions on how to trim the cable properly?
So my current tests have led me to this point:
1) On a fresh reboot of the computer, I plug in the cable. dmesg records:
[ 236.666847] usb 1-2: new full-speed USB device number 6 using xhci_hcd
[ 236.815784] usb 1-2: New USB device found, idVendor=067b, idProduct=2303
[ 236.815792] usb 1-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 236.815796] usb 1-2: Product: USB-Serial Controller
[ 236.815800] usb 1-2: Manufacturer: Prolific Technology Inc.
[ 238.404233] usbcore: registered new interface driver usbserial_generic
[ 238.404281] usbserial: USB Serial support registered for generic
[ 238.411330] usbcore: registered new interface driver pl2303
[ 238.411658] usbserial: USB Serial support registered for pl2303
[ 238.412585] pl2303 1-2:1.0: pl2303 converter detected
[ 238.414588] usb 1-2: pl2303 converter now attached to ttyUSB0
and we have
$ la /dev/ttyU*
crw-rw---- 1 root dialout 188, 0 Feb 18 09:32 /dev/ttyUSB0
2) I start chirpw and select Download from Radio which fails with
[Errno 16] could not open port /dev/ttyUSB0:
[Errno 16] Device or resource busy: '/dev/ttyUSB0'
dmesg now shows:
[ 308.507632] usb 1-2: reset full-speed USB device number 6 using xhci_hcd
[ 308.635386] usb 1-2: device descriptor read/64, error -71
[ 308.871081] usb 1-2: device descriptor read/64, error -71
[ 309.107291] usb 1-2: reset full-speed USB device number 6 using xhci_hcd
[ 309.235327] usb 1-2: device descriptor read/64, error -71
[ 309.471350] usb 1-2: device descriptor read/64, error -71
[ 309.707373] usb 1-2: reset full-speed USB device number 6 using xhci_hcd
[ 309.707623] usb 1-2: Device not responding to setup address.
[ 309.915475] usb 1-2: Device not responding to setup address.
[ 310.123045] usb 1-2: device not accepting address 6, error -71
[ 310.251215] usb 1-2: reset full-speed USB device number 6 using xhci_hcd
[ 310.251475] usb 1-2: Device not responding to setup address.
[ 310.459467] usb 1-2: Device not responding to setup address.
[ 310.667256] usb 1-2: device not accepting address 6, error -71
[ 310.667475] usb 1-2: USB disconnect, device number 6
[ 310.668036] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[ 310.668175] pl2303 1-2:1.0: device disconnected
[ 310.795035] usb 1-2: new full-speed USB device number 7 using xhci_hcd
[ 310.923062] usb 1-2: device descriptor read/64, error -71
[ 311.159198] usb 1-2: device descriptor read/64, error -71
[ 311.395184] usb 1-2: new full-speed USB device number 8 using xhci_hcd
[ 311.523271] usb 1-2: device descriptor read/64, error -71
[ 311.762954] usb 1-2: device descriptor read/64, error -71
[ 311.871262] usb usb1-port2: attempt power cycle
[ 312.523242] usb 1-2: new full-speed USB device number 9 using xhci_hcd
[ 312.523471] usb 1-2: Device not responding to setup address.
[ 312.731488] usb 1-2: Device not responding to setup address.
[ 312.939107] usb 1-2: device not accepting address 9, error -71
[ 313.067232] usb 1-2: new full-speed USB device number 10 using xhci_hcd
[ 313.067438] usb 1-2: Device not responding to setup address.
[ 313.275458] usb 1-2: Device not responding to setup address.
[ 313.483203] usb 1-2: device not accepting address 10, error -71
[ 313.483329] usb usb1-port2: unable to enumerate USB device
and /dev/ttyUSB0 has disappeared:
$ la /dev/ttyU*
ls: cannot access '/dev/ttyU*': No such file or directory
As an experiment I tried the exact same thing, but only plugging the USB
cable into the computer, NOT the radio. This time, on selecting "Download from
Radio", chirpw opens the Cloning.... dialog box for a couple of seconds, then
reports: Radio did not respond. Furthermore, /dev/ttyUSB0 does not disappear in
this situation.
BTW, the firmware on my radio is BFB297. Does that have any bearing on what
I'm doing?
Thanks
Kheong.
On Mon, Feb 17, 2020 at 11:42 PM Aubrey Turner <[email protected]>
wrote:
Just out of curiosity, why did you choose to run such an old distribution
(16.04) of Ubuntu on a relatively new laptop?
I just happened to receive a marketing email from Lenovo this morning (I've
bought a few PCs from them in the past) that included the Carbon X1 Gen 7 and I
looked it up. It has USB 3.1 ports (2x Gen 2 Type-C with Thunderbolt and 2x
Gen 1). I'd think that you'd need the latest possible version of Ubuntu (and
the Linux kernel) to support this laptop.
Looking at the Ubuntu certification page for the Carbon X1, it shows as
having been tested with Ubuntu 18.04 LTS 64-bit.
Your symptoms (device appears, disappears, works sometimes but not others)
could be due to instability in the underlying kernel support for the
motherboard and/or USB controllers.
Another issue to investigate is the use of USB 3.1 ports. In the past
there have been issues with USB 3 ports causing RF interference with devices
that are connected. This mostly manifests with wireless keyboards and mice,
but it wouldn't surprise me if it was an issue here. The common fix is to use
a USB extension cable to move the USB device away from the port.
On 2/17/20 7:39 AM, Kheong Sann CHAN wrote:
I had connected the cable, tried to access it from chirpw causing it to
disconnect a few times, by the time I did dmesg. I removed out the multiple
connect/disconnect lines from dmesg output because the information was mostly
duplicate.
On Mon, Feb 17, 2020 at 7:24 PM Tom Henderson <[email protected]> wrote:
Just double checking here. The log messages below show the cable
connecting, and then disconnecting. Had you disconnected the cable again before
running dmesg, or did the cable fail?
Tom HendersonOn 2/16/20 11:56 PM, Kheong Sann CHAN wrote:
The tty port is found when I plug it in:
$ dmesg | grep tty
[ 7527.188154] usb 1-2: pl2303 converter now attached to ttyUSB0
[ 7548.490452] pl2303 ttyUSB0: pl2303 converter now disconnected from
ttyUSB0
_______________________________________________
chirp_users mailing list
[email protected]
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to kheong sann at [email protected]
To unsubscribe, send an email to
[email protected]
_______________________________________________
chirp_users mailing list
[email protected]
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Aubrey Turner at [email protected]
To unsubscribe, send an email to
[email protected]_______________________________________________
chirp_users mailing list
[email protected]
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to kheong sann at [email protected]
To unsubscribe, send an email to
[email protected]
------------------------------------------------------------------------------
_______________________________________________
chirp_users mailing list
[email protected]
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Glenn at [email protected]
To unsubscribe, send an email to
[email protected]_______________________________________________
chirp_users mailing list
[email protected]
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to [email protected] at [email protected]
To unsubscribe, send an email to [email protected]
