Hello Juan: > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:cisco-nsp- > [EMAIL PROTECTED] On Behalf Of Juan C. Crespo R. > Sent: Thursday, March 29, 2007 6:51 AM > To: [email protected] > Subject: Re: [c-nsp] Catalyst 2950G Trunking Issue > > Reposting.... > > SWITCH-A#show interfaces gigabitEthernet 0/1 trunk > > Port Mode Encapsulation Status Native vlan > Gi0/1 on 802.1q trunking 1 > > Port Vlans allowed on trunk > Gi0/1 1,10-25,354,456,845 > > Port Vlans allowed and active in management domain > Gi0/1 1 > > Port Vlans in spanning tree forwarding state and not pruned > Gi0/1 1 > > > SWITCH-A#show interfaces vlan 1 > Vlan1 is up, line protocol is up > Hardware is CPU Interface, address is 03b0.24b1.5180 (bia > 03b0.24b1.5180) > Internet address is 10.0.0.1/24 > MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation ARPA, loopback not set > ARP type: ARPA, ARP Timeout 04:00:00 > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 25 packets input, 3264 bytes, 0 no buffer > Received 0 broadcasts (0 IP multicast) > 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > 164 packets output, 0 bytes, 0 underruns > 0 output errors, 4 interface resets > 0 output buffer failures, 0 output buffers swapped out > > SWITCH-A# show arp > Protocol Address Age (min) Hardware Addr Type Interface > Internet 10.0.0.1 - 03b0.24b1.5180 ARPA Vlan1 > > > SWITCH-B#show interfaces gigabitEthernet 0/1 trunk > > Port Mode Encapsulation Status Native vlan > Gi0/1 on 802.1q trunking 1 > > Port Vlans allowed on trunk > Gi0/1 1,10-25,354,456,845 > > Port Vlans allowed and active in management domain > Gi0/1 1 > > Port Vlans in spanning tree forwarding state and not pruned > Gi0/1 1 > > > SWITCH-B#show interfaces vlan 1 > Vlan1 is up, line protocol is up > Hardware is CPU Interface, address is 03b2.24b1.5180 (bia > 03b2.24b1.5180) > Internet address is 10.0.0.2/24 > MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation ARPA, loopback not set > ARP type: ARPA, ARP Timeout 04:00:00 > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 210 packets input, 15072 bytes, 0 no buffer > Received 0 broadcasts (0 IP multicast) > 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > 34 packets output, 0 bytes, 0 underruns > 0 output errors, 4 interface resets > 0 output buffer failures, 0 output buffers swapped out > > SWITCH-B# show arp > Protocol Address Age (min) Hardware Addr Type Interface > Internet 10.0.0.2 - 03b2.24b1.5180 ARPA Vlan1 > > > > SWITCH-B#ping 10.0.0.1 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5) > > > > SWITCH-A#ping 10.0.0.2 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5) > SWITCH-A# >
Depending on whether or not your switch is running in L2 or L3 mode, do you have either a default route, default-gateway or both? For testing, you may want to set the appropriate variable to the other device. Mike _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
