The problem is that this link is very important... I've trusted that will be some other solution for this:(
You think that if the TX/RX is now inverted, the network works (with some errors)? -----Original Message----- From: Koch, Christian [mailto:[EMAIL PROTECTED] Sent: Tuesday, April 03, 2007 4:56 PM To: Bagosi Rómeó; [email protected] Subject: RE: [c-nsp] %LINK-4-ERROR and %CDP-4-DUPLEX_MISMATCH have you tried swapping out the fiber? Maybe switching tx/rx ? |-----Original Message----- |From: Bagosi Rómeó [mailto:[EMAIL PROTECTED] |Sent: Tuesday, April 03, 2007 10:53 AM |To: Koch, Christian; [email protected] |Subject: RE: [c-nsp] %LINK-4-ERROR and %CDP-4-DUPLEX_MISMATCH | |Hi Christian! | |I don't tried it, but on the C2924 I cannot change the media |type, only on the C2960 side... |I think the media type on the C2960 is set to auto, and it |recognizes as SFP. I think this is ok... | |C2960: Half-duplex, 100Mb/s, link type is auto, media type is |100BaseFX SFP | | |-----Original Message----- |From: Koch, Christian [mailto:[EMAIL PROTECTED] |Sent: Tuesday, April 03, 2007 2:44 PM |To: Bagosi Rómeó; [email protected] |Subject: RE: [c-nsp] %LINK-4-ERROR and %CDP-4-DUPLEX_MISMATCH | |Try setting the media type under the interface on the 2924? | ||-----Original Message----- ||From: [EMAIL PROTECTED] ||[mailto:[EMAIL PROTECTED] On Behalf Of Bagosi Rómeó ||Sent: Tuesday, April 03, 2007 5:27 AM ||To: [email protected] ||Subject: [c-nsp] %LINK-4-ERROR and %CDP-4-DUPLEX_MISMATCH || ||Hi all Experts! || || || ||I have the following problem: || ||We have two switch connected by fiber cable: || || || ||WS-C2960G-24TC-L:Gi0/21<<<<< >>>>> Fa1/4:WS-C2924M-XL || || FIBER || || || ||The problem is, that the C2924 Switch sends the following messages in ||every minute: || || || ||Apr 3 08:11:33.112 MET-DST: %LINK-4-ERROR: FastEthernet1/4 is ||experiencing errors || || || ||On the C2960 I cannot change the duplex or the speed settings. || ||On the C2924 I've changed the duplex settings, but: || ||- If it's set to duplex auto or duplex full, then ||%CDP-4-DUPLEX_MISMATCH error on the C2960 Switch || ||- If it's set to duplex half, then %LINK-4-ERROR on ||the C2924 Switch || || || ||Why the newer Cisco Devices and IOS doesn't support the speed and ||duplex settings? || ||Does these errors highly affect the network performance? || ||Is there any solution for this problem? || || || || || ||Thank you in anticipation! || || || || || ||C2924# sh int fa1/4 || ||FastEthernet1/4 is up, line protocol is up || || Hardware is Fast Ethernet, address is 0004.9a20.63e0 (bia ||0004.9a20.63e0) || || MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, || || reliability 250/255, txload 7/255, rxload 1/255 || || Encapsulation ARPA, loopback not set || || Keepalive not set || || Half-duplex, 100Mb/s, 100BaseFX || || ARP type: ARPA, ARP Timeout 04:00:00 || || Last input 00:00:06, output 00:00:00, output hang never || || Last clearing of "show interface" counters never || || Queueing strategy: fifo || || Output queue 0/40, 0 drops; input queue 0/75, 0 drops || || 5 minute input rate 588000 bits/sec, 440 packets/sec || || 5 minute output rate 2890000 bits/sec, 530 packets/sec || || 1752297879 packets input, 4205642061 bytes || || Received 6728883 broadcasts, 0 runts, 0 giants, 0 throttles || || 5814363 input errors, 5814363 CRC, 0 frame, 58583 overrun, 61143 ||ignored || || 0 watchdog, 1817612 multicast || || 0 input packets with dribble condition detected || || 2107649242 packets output, 3958607124 bytes, 12 underruns || || 12023160 output errors, 7511084 collisions, 8 interface resets || || 0 babbles, 12023160 late collision, 12054327 deferred || || 0 lost carrier, 0 no carrier || || 12 output buffer failures, 0 output buffers swapped out || || || ||C2960#sh int Gi0/21 || ||GigabitEthernet0/21 is up, line protocol is up (connected) || || Hardware is Gigabit Ethernet, address is 0018.73ec.5b95 (bia ||0018.73ec.5b95) || || MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, || || reliability 252/255, txload 1/255, rxload 6/255 || || Encapsulation ARPA, loopback not set || || Keepalive not set || || Half-duplex, 100Mb/s, link type is auto, media type is 100BaseFX SFP || || input flow-control is off, output flow-control is unsupported || || ARP type: ARPA, ARP Timeout 04:00:00 || || Last input 00:00:00, output 00:00:04, output hang never || || Last clearing of "show interface" counters never || || Input queue: 0/75/0/0 (size/max/drops/flushes); Total |output drops: 0 || || Queueing strategy: fifo || || Output queue: 0/40 (size/max) || || 5 minute input rate 2735000 bits/sec, 519 packets/sec || || 5 minute output rate 599000 bits/sec, 440 packets/sec || || 1744270788 packets input, 3129573151 bytes, 0 no buffer || || Received 61767996 broadcasts (0 multicast) || || 0 runts, 0 giants, 0 throttles || || 11288249 input errors, 11288249 CRC, 0 frame, 0 overrun, |0 ignored || || 0 watchdog, 16264953 multicast, 0 pause input || || 0 input packets with dribble condition detected || || 1466543564 packets output, 2681409739 bytes, 0 underruns || || 0 output errors, 15260833 collisions, 1 interface resets || || 0 babbles, 6268873 late collision, 0 deferred || || 0 lost carrier, 0 no carrier, 0 PAUSE output || || 0 output buffer failures, 0 output buffers swapped out || || || || || ||_______________________________________________ ||cisco-nsp mailing list [email protected] ||https://puck.nether.net/mailman/listinfo/cisco-nsp ||archive at http://puck.nether.net/pipermail/cisco-nsp/ || | _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
