Peter You may want to start with this
http://www.cisco.com/warp/public/116/show_ce1.html I think you will find what you are after on this page or off one of the links at the bottom -- Kind Regards Jarrod Friedland Communications Analyst Oceania ------------------------------------------------------------------------ ------------------ D H L P: +61 7 3845 7735 * M: +61 401 500 134 * F: +61 7 3825 7979 E-mail: [EMAIL PROTECTED] * www: http://www.dhl.com/ 10 Boronia Road Eagle Farm Queensland 4009 > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:cisco-nsp- > [EMAIL PROTECTED] On Behalf Of Peter Nyamukusa > Sent: Thursday, 17 May 2007 3:24 AM > To: [email protected] > Subject: [c-nsp] Channelized E1/PRI Problem > > Hi Folks, > > > > I have just installed a Channelized E1/PRI card on my 3725 router and I am > getting a local alarm from the E1 card could it be possible that the > Chassis > is not compatible to the card. I have pasted the show version & show > controllers from my router, any help is appreciated in pointing me in the > right direction > > > > System image file is "slot0:c3725-is-mz.123-13a.bin" > > > > cisco 3725 (R7000) processor (revision 0.1) with 245760K/16384K bytes of > memory. > > Processor board ID FCZ09487019 > > R7000 CPU at 240MHz, Implementation 39, Rev 3.3, 256KB L2 Cache > > Channelized E1, Version 1.0. > > Bridging software. > > X.25 software, Version 3.0.0. > > SuperLAT software (copyright 1990 by Meridian Technology Corp). > > Primary Rate ISDN software, Version 1.1. > > 2 FastEthernet/IEEE 802.3 interface(s) > > 8 Low-speed serial(sync/async) network interface(s) > > 2 Channelized E1/PRI port(s) > > DRAM configuration is 64 bits wide with parity disabled. > > 55K bytes of non-volatile configuration memory. > > 31360K bytes of ATA System CompactFlash (Read/Write) > > 62720K bytes of ATA Slot0 CompactFlash (Read/Write) > > > > > > show controllers e1 2/0 > > E1 2/0 is down. > > Applique type is Channelized E1 - balanced > > Transmitter is sending remote alarm. > > Receiver has loss of signal. > > alarm-trigger is not set > > Framing is CRC4, Line Code is HDB3, Clock Source is Line. > > Data in current interval (323 seconds elapsed): > > 0 Line Code Violations, 0 Path Code Violations > > 0 Slip Secs, 323 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins > > 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 323 Unavail > Secs > > Data in Interval 1: > > 0 Line Code Violations, 0 Path Code Violations > > 0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins > > 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail > Secs > > > > Peter > > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
