use: service unsupported-transceiver just paste it in conf t, you won't find it with the question mark.
Ulysses Maciel da Costa wrote: > > > I've installed a new SFP module in my Cisco Catalyst from Finisar company to > link up with and Extreme Summit 48. When the system goes up, it send me this > two messages: > > > > 00:01:06: %GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR: GBIC in port 65558 has > bad crc > > 00:01:10: %PM-4-ERR_DISABLE: gbic-invalid error detected on Gi0/21, putting > Gi0/21 in err-disable state > > > > So I've disabled the errdisasble causes to gbic-invalid: > > > > #no errdisable detect cause gbic-invalid > > > > When I configured this, the interface wasn't disable but the > %GBIC_SECURITY_CRYP pesisted. I founded an explanation for this problem: > > > > Error Message GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR: GBIC in port [dec] > has bad > crc. > > Explanation This message means that the GBIC module was identified as a > Cisco GBIC module, but it does not have a valid CRC in the EEPROM data. > [dec] is the interface in which the module is installed. > > Recommended Action Verify that the software release that is running on > the system supports the GBIC module. If the GBIC module is newer, a system > software upgrade might be required. Even if the GBIC module is unrecognized > by the system, the GBIC module might still operate properly, but it will > have limited functionality. > > After that, my switch's status bring this printouts: > > > > > > #sh interfaces gigabitEthernet 0/21 status > > > > Port Name Status Vlan Duplex Speed Type > > Gi0/21 notconnect 1 auto auto unknown > > > > > > > > > > #sh etherchannel detail > > Channel-group listing: > > ---------------------- > > > > Group: 1 > > ---------- > > Group state = L2 > > Ports: 1 Maxports = 8 > > Port-channels: 1 Max Port-channels = 1 > > Protocol: - > > Ports in the group: > > ------------------- > > Port: Gi0/21 > > ------------ > > > > Port state = Down Not-in-Bndl > > Channel group = 1 Mode = On/FEC Gcchange = - > > Port-channel = null GC = - Pseudo port-channel = Po1 > > Port index = 0 Load = 0x00 Protocol = - > > > > Age of the port in the current state: 00d:00h:03m:04s > > > > Port-channels in the group: > > --------------------------- > > > > Port-channel: Po1 > > ------------ > > > > Age of the Port-channel = 00d:00h:02m:08s > > Logical slot/port = 2/1 Number of ports = 0 > > GC = 0x00000000 HotStandBy port = null > > Port state = Port-channel Ag-Not-Inuse > > Protocol = - > > > > > > > > I've tried configure the port-channels, and insert the fiber cable, without > success, does not connect. > > > > Please, someone knows something that I can do in the CatOS conff, than not > buy a new module? > > > > > > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > -- Dan Sabau TBM Invest Manager Tehnic Date 0740078983 -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
