try 'interface ethernet1 auto' or 'no interface ethernet1 auto shutdown' You can see in the configuration that its currently in shutdown mode.
Regards, W On 25/02/2008, Peter Nyamukusa <[EMAIL PROTECTED]> wrote: > Here it is below > I have only put the Ip as I am trying to login to the PDM > > : > PIX Version 6.3(3) > interface ethernet0 auto shutdown > interface ethernet1 auto shutdown > nameif ethernet0 outside security0 > nameif ethernet1 inside security100 > enable password 8Ry2YjIyt7RRXU24 encrypted > passwd 2KFQnbNIdI.2KYOU encrypted > hostname pixfirewall > fixup protocol dns maximum-length 512 > fixup protocol ftp 21 > fixup protocol h323 h225 1720 > fixup protocol h323 ras 1718-1719 > fixup protocol http 80 > fixup protocol rsh 514 > fixup protocol rtsp 554 > fixup protocol sip 5060 > fixup protocol sip udp 5060 > fixup protocol skinny 2000 > fixup protocol smtp 25 > fixup protocol sqlnet 1521 > fixup protocol tftp 69 > names > pager lines 24 > mtu outside 1500 > mtu inside 1500 > no ip address outside > ip address inside 192.168.1.1 255.255.255.0 > ip audit info action alarm > ip audit attack action alarm > no failover > failover timeout 0:00:00 > failover poll 15 > no failover ip address outside > no failover ip address inside > pdm history enable > arp timeout 14400 > timeout xlate 3:00:00 > timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 > 1:00:00 > timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 > timeout uauth 0:05:00 absolute > aaa-server TACACS+ protocol tacacs+ > aaa-server RADIUS protocol radius > aaa-server LOCAL protocol local > http server enable > http 192.168.1.2 255.255.255.255 inside > no snmp-server location > > no failover ip address inside > pdm history enable > arp timeout 14400 > timeout xlate 3:00:00 > timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 > 1:00:00 > timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 > timeout uauth 0:05:00 absolute > aaa-server TACACS+ protocol tacacs+ > aaa-server RADIUS protocol radius > aaa-server LOCAL protocol local > http server enable > http 192.168.1.2 255.255.255.255 inside > no snmp-server location > no snmp-server contact > snmp-server community public > no snmp-server enable traps > floodguard enable > telnet timeout 5 > ssh timeout 5 > console timeout 0 > terminal width 80 > Cryptochecksum:3412014cce8cca04731da9f09bf1fa32 > : end > > > > > -----Original Message----- > From: William [mailto:[EMAIL PROTECTED] > Sent: Monday, February 25, 2008 3:39 PM > To: Peter Nyamukusa > Cc: [email protected] > Subject: Re: [c-nsp] Strange PIX interface problem > > Peter can you include a 'show run' ? > > On 25/02/2008, Peter Nyamukusa <[EMAIL PROTECTED]> wrote: > > > > Hi folks, > > > > I just reset a Pix 515E to factory default using the command "wr erase". > > I am now trying to reconfigure it again and it looks like everything is > > working fine except the interfaces I cannot seem to bring them up > > When I type the command interface Ethernet 1 form the config prompt its > > simply returns and does not change to PIX(config-if) there is also no > error > > deplayed. Just wondering if any one has come across this before or it > could > > just be a bug > > > > pixfirewall(config)# int e1 > > pixfirewall(config)# sh int e1 > > interface ethernet1 "inside" is administratively down, line protocol is > down > > Hardware is i82559 ethernet, address is 0012.7f5b.deee > > IP address 192.168.1.1, subnet mask 255.255.255.0 > > MTU 1500 bytes, BW 10000 Kbit half duplex > > 305 packets input, 27324 bytes, 0 no buffer > > Received 305 broadcasts, 0 runts, 0 giants > > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > > 0 packets output, 0 bytes, 0 underruns > > 0 output errors, 0 collisions, 0 interface resets > > 0 babbles, 0 late collisions, 0 deferred > > 0 lost carrier, 0 no carrier > > input queue (curr/max blocks): hardware (128/128) software (0/0) > > output queue (curr/max blocks): hardware (0/0) software (0/0) > > > > Cisco PIX Firewall Version 6.3(3) > > Cisco PIX Device Manager Version 3.0(1) > > > > Compiled on Wed 13-Aug-03 13:55 by morlee > > > > pixfirewall up 2 hours 3 mins > > > > Hardware: PIX-515E, 64 MB RAM, CPU Pentium II 433 MHz > > Flash E28F128J3 @ 0x300, 16MB > > BIOS Flash AM29F400B @ 0xfffd8000, 32KB > > > > Encryption hardware device : Crypto5823 (revision 0x1) > > 0: ethernet0: address is 0012.7f5b.deed, irq 10 > > 1: ethernet1: address is 0012.7f5b.deee, irq 11 > > Licensed Features: > > Failover: Enabled > > VPN-DES: Enabled > > VPN-3DES-AES: Disabled > > Maximum Physical Interfaces: 6 > > Maximum Interfaces: 10 > > Cut-through Proxy: Enabled > > Guards: Enabled > > URL-filtering: Enabled > > Inside Hosts: Unlimited > > Throughput: Unlimited > > IKE peers: Unlimited > > > > This PIX has an Unrestricted (UR) license. > > > > Serial Number: 808440708 (0x302fd384) > > Running Activation Key: 0x2fab0bdd 0x7a16e505 0xc2402929 0x96e856cd > > > > > > Cheers Peter > > > > > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
