Use the mac address, whats the big deal? they use it for security filtering. You can also specify in bba-group
Here is a configlet distilled from a working system. aaa group server radius radiusgroup server xx.yy.132.7 auth-port 1812 acct-port 1813 server xx.yy.32.37 auth-port 1812 acct-port 1813 deadtime 1 ! vc-class atm vzdsl no ilmi manage oam-pvc manage encapsulation aal5autoppp Virtual-Template1 ! ip local pool DSL-POOL xxx.yyy.146.192 xxx.yyy.146.223 ! aaa authentication ppp default local group radiusgroup aaa authentication ppp radiusgroup group radiusgroup aaa authorization network default local group radiusgroup aaa authorization network radiusgroup group radiusgroup aaa accounting delay-start aaa accounting update periodic 5 aaa accounting network default start-stop group radiusgroup aaa accounting system default start-stop group radiusgroup ! interface Loopback0 ip address xx.yy.15.248 255.255.255.255 ! bba-group pppoe global virtual-template 1 sessions max limit 500 sessions per-mac limit 4 sessions per-vc throttle 30 10 10 sessions per-mac throttle 10 30 30 sessions auto cleanup ! interface Virtual-Template1 ip unnumbered Loopback0 ip verify unicast source reachable-via rx ip route-cache policy ip route-cache flow ip tcp adjust-mss 1452 peer default ip address pool DSL-POOL ppp authentication pap radiusgroup ppp authorization radiusgroup ppp ipcp address required interface ATM2/1/0.20032 point-to-point ip address xx.xx.xx.49 255.255.255.248 class-int vzdsl atm route-bridged ip pvc 2/32 interface ATM2/1/0.500 multipoint description ADSL NY LATA 132 SPID xxxx class-int vzdsl range PPPOE-01 pvc 1/500 1/599 create on-demand radius-server attribute 218 mandatory radius-server attribute nas-port format d radius-server host xx.yyy.32.37 auth-port 1812 acct-port 1813 key THEKEY radius-server host xx.yyy.132.7 auth-port 1812 acct-port 1813 key THEKEY radius-server vsa send authentication Paul A wrote: > Joe, cisco recommends that I use a bba-group if im going to have RBE and > PPPOE on the same interface. > > Currently all of my RBE DSL's use the mac-address below. > > I forgot how I configured that mac-address under the atm interface and how I > can go about configuring another mac address for the bba-group. > > Let me know if you have any ideas and I appreciate the response. > > > > Thanks, > > ---------------------------------------------------- > Paulo Amaral > MegaNet Communications > P: 508 646 0030 > ----------------------------------------------------- > > P.A > -----Original Message----- > P.A > From: Joe Maimon [mailto:[EMAIL PROTECTED] > P.A > Sent: Tuesday, May 06, 2008 3:50 PM > P.A > To: Paul A > P.A > Subject: Re: [c-nsp] RBE and PPPOE on the same router > P.A > > P.A > You can put a mac-address on the atm interface with the mac-address > P.A > command. It need have nothing to do with any ethernet interfaces. > P.A > > P.A > Paul A wrote: > P.A > > Hi, folks hope someone here can clue me in on what I need to do. > P.A > > > P.A > > I currently have a cisco 7200 that I setup a while back for RBE DSL > P.A > and it's > P.A > > been working great with no issues. We also have a redback > P.A > terminating > P.A > > DSL/PPPOE that we want to shutdown. What we are going to do is move > P.A > the > P.A > > PPPOE customers from the redback to the same cisco as the RBE DSL > P.A > customers. > P.A > > > P.A > > The PPPOE customers will be on different VPI/VCI's so I'm assuming I > P.A > can > P.A > > have RBE and PPPOE coexist without issues. The telco needs to know > P.A > my mac > P.A > > address for the cisco to add to their bridge table. Looking at my > P.A > config I > P.A > > noticed I have a mac-address on the ATM, mac-address 0000.0cca.22dc. > P.A > > > P.A > > Should this mac-address be the fast0 interface's mac address thats > P.A > connected > P.A > > to the gateway? I'm trying to figure out what mac-address they are > P.A > looking > P.A > > for. > P.A > > > P.A > > I would apriciate if someone could point me in the direction for > P.A > getting > P.A > > RBE/PPPOE working together on the same router. > P.A > > > P.A > > > P.A > > interface ATM5/0 > P.A > > description VZ CIRTUIT ID 95HFGJ6XXXX > P.A > > mac-address 0000.0cca.22dc > P.A > > no ip address > P.A > > no ip redirects > P.A > > no ip unreachables > P.A > > ip route-cache policy > P.A > > ip route-cache flow > P.A > > load-interval 30 > P.A > > no atm oversubscribe > P.A > > atm scrambling cell-payload > P.A > > atm uni-version 3.1 > P.A > > atm ilmi-keepalive > P.A > > arp arpa > P.A > > arp timeout 0 > P.A > > ! > P.A > > interface ATM5/0.100201 point-to-point > P.A > > ip unnumbered Loopback1 > P.A > > ip access-group dsl-inbound in > P.A > > no ip redirects > P.A > > no ip unreachables > P.A > > ip nat inside > P.A > > ip virtual-reassembly > P.A > > ip route-cache same-interface > P.A > > no ip mroute-cache > P.A > > ip policy route-map FA20RM > P.A > > no snmp trap link-status > P.A > > atm route-bridged ip > P.A > > pvc 1/201 > P.A > > encapsulation aal5snap > P.A > > service-policy output fbwfq > P.A > > > P.A > > Thanks, > P.A > > > P.A > > ---------------------------------------------------- > P.A > > Paulo Amaral > P.A > > MegaNet Communications > P.A > > P: 508 646 0030 > P.A > > ----------------------------------------------------- > P.A > > > P.A > > _______________________________________________ > P.A > > cisco-nsp mailing list [email protected] > P.A > > https://puck.nether.net/mailman/listinfo/cisco-nsp > P.A > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > P.A > > > P.A > > > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
