You need 12.0(33)S1 Starting in Cisco IOS Release 12.0(33)S, Engine 5 line cards are also supported as the egress interface on which you can configure a virtual interface (EtherChannel or POS channel) for a link bundle. For a list of supported Engine 5 interfaces, see Line Cards Supported on the Cisco 12000 Router<http://www.cisco.com/en/US/docs/ios/12_0s/feature/guide/lnkbndl.html#wp1041951>.
Nitzan On Tue, Sep 16, 2008 at 18:57, Mark Tech <[EMAIL PROTECTED]> wrote: > Hi, thanks for that. Just had a look at my inventory > > sh inventory > NAME: "slot 0", DESCR: "ISE 10G Modular Services Card v2" > PID: 12000-SIP-601 , VID: V04, SN: SAD12340460 > > Looks like I have an ISE card installed. If I look at the restrictions for > the ISE, seems like only the following cards are supported: > > IP Service Engine (ISE): > –4-port Gigabit Ethernet ISE line card > –4-port OC-3c/STM-1c POS/SDH ISE line card > –8-port OC-3c/STM-1c POS/SDH ISE line card > –16-port OC-3c/STM-1c POS/SDH ISE line card > –4-port OC-12c/STM-4c POS/SDH ISE line card > –1-port OC-48c/STM-16c POS/SDH ISE line card > > However it then goes to mention that the following cards support it. > > Engine 5 SPA Interface Processors (SIPs): > –10G Engine 5 SPA Interface Processor (12000-SIP-600) > –2.5G multiservice engine SPA Interface Processor (12000-SIP-401) > –5G multiservice engine SPA Interface Processor (12000-SIP-501) > –10G multiservice engine SPA Interface Processor (12000-SIP-601) > > The GE cards are installed in a 12000-SIP-601, or is that I don't have > an'Engine 5' within the 601installed? > > Regards > > Mark > > > > ----- Original Message ---- > From: Leonardo Gama Souza <[EMAIL PROTECTED]> > To: Mark Tech <[EMAIL PROTECTED]> > Cc: cisco-nsp@puck.nether.net > Sent: Tuesday, September 16, 2008 3:49:54 PM > Subject: RES: [c-nsp] Cisco 12406 Etherchannel > > > There are some restrictions... > Take a look: > http://www.cisco.com/en/US/docs/ios/12_0s/feature/guide/lnkbndl.html > > Cheers. > > ________________________________ > De: [EMAIL PROTECTED] em nome de Mark Tech > Enviada: ter 16/9/2008 08:12 > Para: cisco-nsp@puck.nether.net > Assunto: [c-nsp] Cisco 12406 Etherchannel > > > Hi > I am trying to configure Ethernchannel/link bundling on a 12406. The port > channel seems to be accepted, however when I try and add a channel-group to > my GE interfaces, it says its not supported? I am using SPA-10X1GE-V2 line > cards with c12kprp-p-mz.120-32.SY6.bin IOS > > > interface Port-channel1 > ip address x.x.x.x 255.255.255.252 > no ip directed-broadcast > channel-group minimum active 1 > no channel-group bandwidth control-propagation > > router(config-if)#channel-group 1 > Error: not supported on GigabitEthernet0/0/0. > > Is there a way to bundle more that 1GE port on a 12406? > > Regards > > Mark > > > > > _______________________________________________ > cisco-nsp mailing list cisco-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > _______________________________________________ > cisco-nsp mailing list cisco-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/