More over in some ios version it comes up but not passing traffic and no label imposed. While in later release it stays down. Hth Hash Sent from my BlackBerry® wireless device from Aljawal
-----Original Message----- From: Shimol Shah <[email protected]> Date: Thu, 20 Aug 2009 13:05:17 To: Atif Sid<[email protected]> Cc: <[email protected]> Subject: Re: [c-nsp] xconnect on VLAN interface ES card On the 7600 for doing SVI EoMPLS (Xconnect under SVI) you need a CWAN card (ES20, SIP400 etc) facing the core. For using Hardware EoMPLS (i.e. with Xconnect under main/single tag subif ) on the 7600, you can use below CE Facing LC: LAN Line Card, ES-20, SIP-600 Core Facing LC: Any Atif Sid said the following on 8/20/2009 12:55 PM: > I have seen posts on this topic but still not clear.. currentl have WS line > cards, with SUP-32 on 7606; PW on VLAN interface do not work. testing ES > card customer facing, RSP-720 core facing, here is the issue.. any help will > be great ! > > Is it possible to configure xconnect from an SVI interface, when your core > facing cards are RSP-720? > > I have configured it: > > interface Vlan290 > no ip address > xconnect 10.10.136.129 37123712 encapsulation mpls > end > > It does not come up: > > PE4#sh mpl l2transport vc > > Local intf Local circuit Dest address VC ID Status > ------------- -------------------------- --------------- ---------- > ---------- > Vl290 Eth VLAN 290 10.10.136.129 37123712 DOWN > > PE4#sh mpl l2transport vc 37123712 det > PE4#sh mpl l2transport vc 37123712 detail > Local interface: Vl290 up, line protocol up, Eth VLAN 290 up > Interworking type is Ethernet > Destination address: 10.10.136.129, VC ID: 37123712, VC status: down > Output interface: none, imposed label stack {} > Preferred path: not configured > Default path: no route > No adjacency > Create time: 00:00:49, last status change time: 00:00:03 > Signaling protocol: LDP, peer 10.10.136.129:0 up > Targeted Hello: 10.10.136.131(LDP Id) -> 10.10.136.129 > Status TLV support (local/remote) : enabled/not supported > Label/status state machine : remote ready, LndRru > Last local dataplane status rcvd: no fault > Last local SSS circuit status rcvd: AC DOWN(rx,tx faults) > Last local SSS circuit status sent: no fault > Last local LDP TLV status sent: no fault (withdrawn) > Last remote LDP TLV status rcvd: not sent > MPLS VC labels: local unassigned, remote 340 > Group ID: local unknown, remote 0 > MTU: local unknown, remote 1500 > Remote interface description: ** Test PW with PE4 ES SVI int ** > Sequencing: receive disabled, send disabled > VC statistics: > packet totals: receive 0, send 0 > byte totals: receive 0, send 0 > packet drops: receive 0, seq error 0, send 0 > > Although when I use a physical interface it comes up? > RSP720 does not support it?? > > moved it to physical interface it comes up: > > interface GigabitEthernet2/1 > no ip address > ip verify unicast source reachable-via any > load-interval 30 > speed 1000 > xconnect 10.10.136.129 37123712 encapsulation mpls > end > > PE4#sh mpls l2transport vc > Local intf Local circuit Dest address VC ID Status > ------------- -------------------------- --------------- ---------- > ---------- > Gi2/1 Ethernet 10.10.136.129 37123712 UP > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
