You need to tell the E1 controller it's to be used as a PRI and what timeslots ie:
contr e1 6/0 pri-group timeslots 1-31 This will create serial interface 6/0:15 and allow you to configure ISDN parameters. Don't forget to set your framing on the controller either. Macca On Tue, Sep 29, 2009 at 4:45 PM, Andy Saykao < [email protected]> wrote: > Hey All, > > I'm new to all this voice stuff... > > We've just installed a AS5400 and plugged the PRI's in but I'm not > seeing the interfaces below show up in the config. > > Eg: > interface Serial6/0:15 > interface Serial6/1:15 > interface Serial6/2:15 > interface Serial6/3:15 > > The Carrier is seeing alarms on their end so it could be that the PRI's > aren't properly activated yet. But regardless of this, am I suppose to > see those serial interfaces present in the config irrespective of > whether the PRIs are up or not? > > When I try to manually add in the interface, it's not recognized. > > as1-ks(config)#interface serial 6/0:15? > % Unrecognized command > > Some more details about the AS... > > as1-ks#sh ver > Cisco IOS Software, 5400 Software (C5400-IS-M), Version 12.4(11)T, > RELEASE SOFTWARE (fc2) > Technical Support: http://www.cisco.com/techsupport > Copyright (c) 1986-2006 by Cisco Systems, Inc. > Compiled Sun 19-Nov-06 00:33 by prod_rel_team > > ROM: System Bootstrap, Version 12.1(2r)XD1, RELEASE SOFTWARE (fc1) > BOOTLDR: 5400 Software (C5400-BOOT-M), Version 12.1(5)T5, RELEASE > SOFTWARE (fc1) > > as1-ks-mel uptime is 40 minutes > System returned to ROM by reload at 15:53:14 AEST Tue Sep 29 2009 > System restarted at 15:54:03 AEST Tue Sep 29 2009 > System image file is "flash:c5400-is-mz.124-11.T.bin" > > Cisco AS5400 (R7K) processor (revision T) with 262144K/65536K bytes of > memory. > Processor board ID JAB042904CY > R7000 CPU at 250MHz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 > Cache > Last reset from IOS reload > Manufacture Cookie Info: > EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x31, > Board Hardware Version 3.27, Item Number 800-5171-01, > Board Revision B0, Serial Number JAB042904CY, > PLD/ISP Version 2.2, Manufacture Date 11-Jul-2000. > Processor 0x14, MAC Address 0001.42b3.5b7e > Backplane HW Revision 1.0, Flash Type 5V > 2 FastEthernet interfaces > 10 Serial interfaces > 216 terminal lines > 16 Channelized E1/PRI ports > 512K bytes of NVRAM. > 32768K bytes of processor board System flash (Read/Write) > 8192K bytes of processor board Boot flash (Read/Write) > > Configuration register is 0x2102 > > as1-ks#sh controllers e1 6/2 > E1 6/2 is down. > Applique type is Channelized E1 - balanced > Far End Block Errors Detected > Receiver has loss of signal. > alarm-trigger is not set > Version info of slot 6: HW: 768, PLD Rev: 1 > Framer Version: 0x8 > > > Thanks. > > Andy > > This email and any files transmitted with it are confidential and intended > solely for the use of the individual or entity to whom they are addressed. > Please notify the sender immediately by email if you have received this > email by mistake and delete this email from your system. Please note that > any views or opinions presented in this email are solely those of the > author and do not necessarily represent those of the organisation. > Finally, the recipient should check this email and any attachments for > the presence of viruses. The organisation accepts no liability for any > damage caused by any virus transmitted by this email. > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
