Hello, My bootvar / confreg looks correct to me, doesn't it ?
BB1.IX1#sh bootvar BOOT variable = sup-bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXH2a.bin,1; CONFIG_FILE variable = BOOTLDR variable = Configuration register is 0x2102 Y. 2010/3/22 William McCall <[email protected]> > Check the conf reg for the sp. IIRC, it also resets the confreg in its > stupidity. I ran into this same bug in production and recall having to > set it again. > > On 3/22/10, Youssef Bengelloun-Zahr <[email protected]> wrote: > > Hello list, > > > > I have tried to debug this for a long time but I'm stuck. Here is the > > situation. > > > > I have a SUP720-3BXL (MSFC3) running on > > s72033-advipservicesk9_wan-mz.122-33.SXH2a.bin that went crazy just > before > > X-mas eve, after two years of loyal services ! > > > > After some log reading, I found out I was affected by bug CSCsc33990 : > > > > Causes and Resolutions: > > * If there is any corruption in the TCAM entries, the *SPRPInbandPing > test > > can fail*. If the test, ran as > > part of Cisco Generic Online Diagnostics (GOLD), fails 10 times > > consecutively, then the supervisor > > engine can crash. > > > > In order to resolve the issue, upgrade the Cisco IOS software to a > release > > not affected by Cisco bug ID > > CSCsc33990 ( registered customers only) . > > > > * If health-monitoring is enabled on the device and complete diagnostics > is > > configured during the > > startup, then the supervisor can crash at the time of the boot process. > > Health-monitoring and complete diagnostics conflict with each other for > some > > tests. As a > > workaround, disable either of them, which depends on your requirement. > > > > > > > > I have taken back the faulty card back to my office where I have a spare > > chassi (comes in handy sometimes ;-) and now the sup720 boots in ROMMON. > > > > I thought maybe my bootdisk (sup-bootflash or sup-bootdisk) whas > corrupted > > because It was old. I tried this : > > > > - boot on disk0 with the same IOS ===> OK > > > > - format bootdisk then copy IOS from disk0: to bootdisk: ===> OK > > > > - Reload with my bootvar pointing to the image on bootdisk: ===> NOK > > > > - from ROMMON, boot using the image on bootdisk: ===> OK (look below for > > output) > > > > > > > > BB1.IX1#reload > > Proceed with reload? [confirm] > > > > *Mar 22 10:23:37.587: %SYS-5-RELOAD: Reload requested by console. Reload > > Reason: Reload Command. > > Mar 22 10:23:41.836: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure > > console debugging output. > > > > Mar 22 10:23:41.836: %OIR-SP-6-CONSOLE: Changing console ownership to > switch > > processor > > > > > > > > Mar 22 10:23:42.040: %SYS-SP-3-LOGGER_FLUSHED: System was paused for > > 00:00:00 to ensure console debugging output. > > > > Mar 22 10:23:44.615: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure > > console debugging output. > > > > > > > > *** > > *** --- SHUTDOWN NOW --- > > *** > > > > Mar 22 10:23:44.615: %SYS-SP-5-RELOAD: Reload requested > > Mar 22 10:23:44.615: %OIR-SP-6-CONSOLE: Changing console ownership to > switch > > processor > > > > > > > > Mar 22 10:23:44.923: %SYS-SP-3-LOGGER_FLUSHED: System was paused for > > 00:00:00 to ensure console debugging output. > > > > System Bootstrap, Version 8.4(2) Release > > Copyright (c) 1994-2005 by cisco Systems, Inc. > > Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory > > > > rommon 1 > > > rommon 1 > > > rommon 1 > dev > > Devices in device table: > > id name > > bootdisk: boot disk > > disk0: PCMCIA Disk 0 > > disk1: PCMCIA Disk 1 > > eprom: eprom > > rommon 2 > dir bootdisk: > > > > Initializing ATA monitor library... > > Directory of bootdisk: > > > > 2 78203396 -rw- s72033-advipservicesk9_wan-mz.122-33.SXH2a.bin > > 3084 33554432 -rw- sea_log.dat > > rommon 3 > > > rommon 3 > > > rommon 3 > boot bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXH2a.bin > > Loading image, please wait ... > > > > > > Initializing ATA monitor library... > > > > > > > > I Decided then to change th CF on the SUP720 with a brand new one, no > > change. I am still experiencing the same symptoms. > > > > > > > > Any ideas what might cause this ? Would you recommend an upgrade in order > to > > solve this ? Is my SUP720 dead ? > > > > Thanks for your feedback. > > > > Best regards. > > > > Y. > > > > -- > > Youssef BENGELLOUN-ZAHR > > ...................................................... > > Ingénieur Réseaux et Télécoms > > > > > > Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 > > Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE > > Tel +33 (0) 825 000 720 > > Tel. direct +33 (0) 1 77 35 59 14 > > Tel. portable +33 (0) 6 22 42 63 80 > > Email [email protected] > > > ............................................................................................... > www.720.fr > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > -- > Sent from my mobile device > > William McCall, CCIE #25044 > -- Youssef BENGELLOUN-ZAHR ……………………………………………… Ingénieur Réseaux et Télécoms Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE Tel +33 (0) 825 000 720 Tel. direct +33 (0) 1 77 35 59 14 Tel. portable +33 (0) 6 22 42 63 80 Email [email protected] ……………………………………………………………………………….....www.720.fr _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
