Am I misreading, or did he say it wasn't under the 'interface vlan', but under the 'vlan' itself? :)
I just looked on mine, and it's under the vlan config (Version 4.2(3) software). NEX7000EDC1(config)# vlan 4 NEX7000EDC1(config-vlan)# ? ip Configure IP features media Media type of the VLAN name Ascii name of the VLAN no Negate a command or set its defaults remote-span Enable remote span VLAN service-policy Configure service policy for an interface shutdown Shutdown VLAN switching state Operational state of the VLAN end Go to exec mode exit Exit from command interpreter pop Pop mode from stack or restore from name push Push current mode to stack or save it under name where Shows the cli context you are in Ken Matlock Network Analyst Exempla Healthcare (303) 467-4671 [email protected] -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Matthew Melbourne Sent: Thursday, September 02, 2010 9:08 AM To: Arie Vayner (avayner) Cc: [email protected] Subject: Re: [c-nsp] N7k: Attaching a service-policy to an SVI The service-policy command doesn't appear to be there under the SVI... nx01(config)# int vlan 304 nx01(config-if)# ? bandwidth Set bandwidth informational parameter carrier-delay Specify delay for interface transitions delay Specify interface throughput delay description Interface specific description hsrp HSRP interface configuration commands inherit Inherit a port-profile ip Configure IP features ipv6 Configure IPv6 features isis IS-IS configuration commands load-interval Specify interval for load calculation for an interface mac-address Manually set interface MAC address medium Configure Interface medium mode mtu Set the interface Maximum Transmission Unit (MTU) no Negate a command or set its defaults shutdown Enable/disable an interface snmp Modify SNMP interface parameters vrf Configure VRF parameters vrrp VRRP configuration commands end Go to exec mode exit Exit from command interpreter pop Pop mode from stack or restore from name push Push current mode to stack or save it under name where Shows the cli context you are in On 2 September 2010 14:43, Arie Vayner (avayner) <[email protected]> wrote: > Matt, > > You should be able to apply the qos policy on the "vlan" (as opposed to > "interface vlan"): > Let me know if it works for you. > > This is the doc, but I think it might be wrong (for the syntax) - let me > know, and I will see internally. > http://www.cisco.com/en/US/docs/switches/datacenter/sw/5_x/nx-os/qos/con > figuration/guide/cpl.html#wp1056677 > > Arie > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Matthew > Melbourne > Sent: Thursday, September 02, 2010 14:18 > To: [email protected] > Subject: [c-nsp] N7k: Attaching a service-policy to an SVI > > Hi, > > Is it possible to attach a QoS service policy (in this case a simple > ICMP policier) to a VLAN interface on the N7k platform (NX-OS > 5.0(2a))? The docs suggest it is possible, but the service-policy > command doesn't appear to be available in interface configuration mode > for an SVI (the command is present under a physical interface). > > Cheers, > > Matt > > -- > Matthew Melbourne > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > -- Matthew Melbourne _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
