It supports both...
There is a PoE model and all of the NetVantas support LLDP.. -- Tim On Tue, Oct 12, 2010 at 8:44 AM, Jason Berenson <[email protected]> wrote: > Looks great, but it doesn't list LLDP or PoE as an option. > > -Jason > > On 10/12/10 9:29 AM, Dave Weis wrote: >> >> I realize it's not a Cisco device but an Adtran 3448 would fit exactly >> what you are trying to do. >> >> http://www.adtran.com/web/page/portal/Adtran/product/4200821E2 >> >> >> >>> -----Original Message----- >>> From: [email protected] >>> [mailto:[email protected]] On Behalf Of Jason Berenson >>> Sent: Monday, October 11, 2010 9:43 PM >>> To: [email protected] >>> Subject: [c-nsp] Small office sanity check >>> >>> Greetings, >>> >>> I'm trying to come up with a small office router/switch >>> configuration. >>> This would be an office with a DSL or T1 with 4-8 IP phones >>> and the same in computers. Requirements are as follows: >>> >>> - Covad split PVC voice/data for QoS >>> - LLDP to dynamically assign VLANs to phones and keep >>> computers in VLAN 1 >>> - DHCP with options capability to send config server >>> information to phones >>> - PoE that can do between 7W and 15W per port >>> - VRF to split voice/data routing >>> - As cheap as possible >>> >>> Here's what I've come up with so far: >>> >>> - Cisco 1721 with ADSL or T1 module >>> - Cisco 300 seris SRW208P-K9-NA >>> >>> Relevant portion of the 1721 config: >>> >>> ip dhcp pool voice >>> vrf voice >>> network 192.168.10.0 255.255.255.0 >>> dns-server 1.1.1.1 2.2.2.2 >>> netbios-node-type h-node >>> default-router 192.168.10.1 >>> option 66 ascii "config-server" >>> lease 30 >>> ! >>> ip vrf voice >>> rd 2:1 >>> route-target export 2:1 >>> route-target import 2:1 >>> >>> interface ATM0 >>> no ip address >>> no atm ilmi-keepalive >>> dsl operating-mode auto >>> ! >>> interface ATM0.1 point-to-point >>> ip address 10.3.5.202 255.255.255.252 >>> pvc 0/35 >>> description DATA >>> encapsulation aal5mux ip >>> ! >>> ! >>> interface ATM0.2 point-to-point >>> ip vrf forwarding voice >>> ip address x.x.x.x 255.255.255.252 >>> pvc 0/36 >>> description VOICE >>> encapsulation aal5mux ip >>> ! >>> ! >>> interface FastEthernet0 >>> no ip address >>> speed 100 >>> full-duplex >>> no cdp enable >>> ! >>> interface FastEthernet0.1 >>> encapsulation dot1Q 1 native >>> ip address y.y.y.y 255.255.255.252 >>> no cdp enable >>> ! >>> interface FastEthernet0.120 >>> encapsulation dot1Q 120 >>> ip vrf forwarding voice >>> ip address 192.168.10.1 255.255.255.0 >>> no cdp enable >>> ! >>> ip nat inside source list 101 interface ATM0.2 vrf voice >>> overload ip classless ip route 0.0.0.0 0.0.0.0 10.3.5.201 >>> name data ip route vrf voice 0.0.0.0 0.0.0.0 y.y.y.z name >>> voice no ip http server ip http authentication local ! >>> ! >>> access-list 101 permit ip 192.168.10.0 0.0.0.255 any >>> >>> This should allow for a routed public net on VLAN 1 for their >>> firewall and a NAT'd network on VLAN 120 for the phones. Any >>> pointers, comments, recommendations are welcome. >>> >>> Thanks, >>> Jason >>> >>> _______________________________________________ >>> cisco-nsp mailing list [email protected] >>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>> archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
