Hi John , Thanks for the reply please find the output below CR1.KJ-Building#sh module Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE1217FPWB 2 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1214LB5N 3 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1203D8UB 5 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL JAF1215DPHH
Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 001d.702f.4400 to 001d.702f.447f 2.5 12.2(33)SRD6 12.2(33)SRD6 Ok 2 001f.6ca1.8300 to 001f.6ca1.830f 4.6 7.2(1) 8.7(0.22)SRD Ok 3 001e.4ad1.bce0 to 001e.4ad1.bd0f 11.3 7.2(1) 8.7(0.22)SRD Ok 5 001e.be6e.7bfc to 001e.be6e.7bff 5.6 8.5(2) 12.2(33)SRD6 Ok Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1/0 5xGE SPA SPA-5X1GE-V2 JAE1216EVQK 1.2 Ok 5 Policy Feature Card 3 WS-F6K-PFC3BXL JAF1213ARCG 1.8 Ok 5 MSFC3 Daughterboard WS-SUP720 JAF1213BJHC 3.1 Ok Mod Online Diag Status ---- ------------------- 1 Pass 1/0 Pass 2 Pass 3 Pass 5 Pass > Date: Mon, 13 Jun 2011 10:13:08 -0400 > From: [email protected] > To: [email protected] > CC: [email protected]; [email protected] > Subject: Re: [c-nsp] Input Queue > > It is likely the flushed traffic is in the input queue to CPU, but a > 6500 can also account for rx queuing drops in this drops counter as an > aggregate counter. > > In the show queueing output, we see 81 packets dropped: > > Packets dropped on Receive: > BPDU packets: 0 > > queue thresh dropped [cos-map] > --------------------------------------------------- > 1 1 81 [0 1 2 3 4 5 6 7 ] > > I would watch the individual interfaces (show queueing interface) to see > if these dropped packets add up to the input queue drops you see on the > port-channel. > > Can you run "show module" for us? > > > Regards, > John Gill > cisco > 919.392.2309 > > On 6/11/11 12:41 PM, Pete Lumbis wrote: > > The input queue is the queue between the interface and the CPU, only > > process switched traffic hits this queue. Drops in the input queue are > > almost always due to a busy CPU. > > > > If you happen to have packets in the queue (the first number is > > greater than 0) you can run "show buffers input interface<INTERFACE> > > dump" and decode the packets. > > > > Also check out this troubleshooting doc > > http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a0080094791.shtml > > > > -Pete > > > > On Fri, Jun 10, 2011 at 7:46 AM, Mohammad Khalil<[email protected]> > > wrote: > >> > >> hi all > >> > >> i have etherchannel consisting of 5 G interfaces > >> the port-channel is assigned to VLAN 10 (SVI created) > >> i cleared the counters on the interface yesterday and today > >> Input queue: 0/75/962/962 (size/max/drops/flushes) > >> what is the issue ? > >> > >> _______________________________________________ > >> cisco-nsp mailing list [email protected] > >> https://puck.nether.net/mailman/listinfo/cisco-nsp > >> archive at http://puck.nether.net/pipermail/cisco-nsp/ > >> > > > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
