What sort of timeframes are we now looking at for the next release of
code for the ME3600/3800X's? There was some talk about new software
supporting VPLS related features coming out in June, and a bunch of
15.0(SE) releases has just turned up on CCO for the lower end floor
switches like the 3560/3750s..
Reuben
On 28/07/2011 9:50 AM, Waris Sagheer (waris) wrote:
ME3600X does not support Netflow and WCCP in the current release.
If the configuration guide does not cover the features then it is not be
supported.
Netflow and WCCP features are not covered in the configuration guide.
-Waris
-----Original Message-----
From: cisco-nsp-boun...@puck.nether.net
[mailto:cisco-nsp-boun...@puck.nether.net] On Behalf Of Colby Glass
Sent: Wednesday, July 27, 2011 4:27 PM
To: Sigurbjörn Birkir Lárusson
Cc: cisco-nsp@puck.nether.net
Subject: Re: [c-nsp] ME3600X Netflow and WCCP?
Thanks guys. Before posting, I noticed that it's listed in the unsupported
commands of an older IOS, but not in the newer one. That gave me some hope.
Though, none of the guides I saw listed anything for configuring WCCP or
Netflow. The feature nav listed WCCP Version 2 though. It's not looking
good.
On Wed, Jul 27, 2011 at 5:59 PM, Sigurbjörn Birkir Lárusson<
sigurbjo...@vodafone.is> wrote:
I wouldn't trust that, you can configure stuff on the ME3600X that doesn't
actually work (or in fact do anything at all) in practice, you can even
configure stuff that is in the manual, and is supposed to work, but still
doesn't work ;)
I turned on flow on a couple of interfaces, turned on top-talkers and got
nothing. I then setup netcat to listen to a UDP port, configured export
to send it, and according to show ip flow export it's not exporting
anything.
It also doesn't bode well for the support that ip flow-export is in the
list of unsupported commands in the configuration guide, nor does the fact
that there is only one reference to wccp in the configuration guide and
that's under the traffic-classifier for the CPU traffic...
Kind regards,
Sibbi
Þann 27.7.2011 21:31, skrifaði "Jason Lixfeld"<ja...@lixfeld.ca>:
On 2011-07-27, at 4:45 PM, Colby Glass wrote:
All,
Does anyone happen to know if the ME3600 supports Netflow and WCCP? I
have a
customer considering them for the WAN edge and the docs/feature
navigator
are coming up somewhat ambiguous.
I haven't tested it, but...
systems02.151front71(config)#ip flow-?
flow-aggregation flow-cache flow-capture flow-egress
flow-export flow-top-talkers
systems02.151front71(config)#ip flow-export ?
destination Specify the Destination IP address
source Specify the interface for source address
template Specify the template specific configurations
version Specify the version number
systems02.151front71(config)#ip flow-export version ?
1
5
9
systems02.151front71(config)#int g0/1
systems02.151front71(config-if)#no switchport
systems02.151front71(config-if)#ip route-cache ?
cef Enable Cisco Express Forwarding
flow Enable Flow fast-switching cache
policy Enable fast-switching policy cache for outgoing packets
same-interface Enable fast-switching on the same interface
<cr>
systems02.151front71(config-if)#ip wccp ?
<0-254> Dynamically defined service identifier number
redirect Set packet redirection options
web-cache Standard web caching service
systems02.151front71(config-if)#
This is on 12.2(52)EY1
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
