Hi, If SNMP is enabled on your switch you can set vlan information for catalyst switches.
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a00801c6035.shtml Best Regards Mohamed Touré On 4 November 2011 01:05, Mohammad Khalil <[email protected]> wrote: > > Thanks a lot for the replies , i know that the switch will not help and i > am in need of some sort of scripting > i will start looking into doing it > > Thanks again > > Best Regards, > Mohammad Khalil > > Date: Thu, 3 Nov 2011 16:51:54 -0700 > From: [email protected] > Subject: Re: [c-nsp] Changing VLANs > To: [email protected] > CC: [email protected] > > Given the original spec, I would suggest something scripted with expect to > telnet to the switch and change the parameters when you need them. You > would then schedule it to run at the time interval you require. > There is nothing native on the switch that is going to do what you want, > you will have to look at external tools. > If you want the PC to renew it's DHCP address every 5 minutes (when you > change the VLAN it's connected to) then you'll also have to get your PC to > drop it's IP and ask for a new one from DHCP at the same time. > > > regards,Tony. > > From: Mohammad Khalil <[email protected]> > To: [email protected]; [email protected] > Cc: [email protected] > Sent: Thursday, 3 November 2011 6:51 PM > Subject: Re: [c-nsp] Changing VLANs > > > Hi , Thank you all > > I had EEM in my mind , but i assumed that the switch is Layer 2 switch > the PC does not support dot1q trunk > the goal is i want to test some WiMAX CPEs (which by default act as a DHCP > server and provide the PC connected with access) > > > CC: [email protected]; [email protected] > > From: [email protected] > > Subject: Re: [c-nsp] Changing VLANs > > Date: Thu, 3 Nov 2011 16:03:43 +1000 > > To: [email protected] > > > > Surely if you have a number of dhcp servers theres a layer3 switch or > router in the network that you can use to route between pc and servers > > > > Sent from my iPhone > > > > On 03/11/2011, at 1:11 PM, "Thomason, Simon" <[email protected]> > wrote: > > > > > You could use EEM and tcl > scripts to do this. > > > > > > > > > -----Original Message----- > > > From: [email protected] [mailto: > [email protected]] On Behalf Of Mohammad Khalil > > > Sent: Thursday, 3 November 2011 4:15 AM > > > To: [email protected] > > > Subject: [c-nsp] Changing VLANs > > > > > > > > > Hi all , i have a layer 2 switch , i want to connect a PC to a port > and number of DHCP servers to other ports > > > i want to the PC to communicate with each server every 5 minutes > > > for example PC is connected to F0/1 and Server 1 is connected to F0/2 > , after 5 minutes i want the port the PC connecting to to change its VLAN > in order to communicate with Server 2 which is connected to port F0/3 > (which is on different VLAN) > > > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
