Hi Dol,
IIRC you need the pppoe-dialer command on the SVI, not the physical
port:
interface FastEthernet0
no pppoe-client dial-pool-number 1
!
interface vlan20
no ip address
pppoe-client dial-pool-number 1
!
Jonesy
On 16.01.2013 14:11, Dol Meun wrote:
Dear All,
I have installed LNS with local authentication with the configuration
below, I have two cisco router one is Cisco 1811 and I am using port
fa0
connected to LNS fast0 then the PPPoE session is working fine. But
for
Cisco C887VA, I am using port Fast 0 on C887 connected to port Fast 1
on
LNS but PPPoE is not working. is there any miss configure in my
configuration or is there any restrict on Cisco C887 port for PPPoE
connection. Note: on Cisco 1811 I use layer 3 port and Router Cisco
887 I
use switchport as shown in the configuration. Is there anyone used to
met
this problem?
*##LNS (LAC and LNS in the same router)*
aaa new-model
!
!
aaa authentication login default local
aaa authentication ppp default local
!
!
aaa session-id common
!
!
dot11 syslog
ip source-route
!
!
!
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
vpdn enable
vpdn multihop
vpdn aaa attribute nas-port vpdn-nas
vpdn redirect
vpdn logging
vpdn logging local
vpdn logging user
vpdn logging tunnel-drop
vpdn history failure table-size 50
vpdn session-limit 1400
vpdn search-order multihop-hostname domain dnis
vpdn domain-delimiter @ suffix
vpdn domain-delimiter / prefix
!
vpdn-group LAC
!
vpdn-group LAC-TEST
request-dialin
protocol l2tp
domain eintellego.net
domain direct.telstra.net
initiate-to ip 192.168.55.2
source-ip 192.168.55.1
local name LAC
l2tp tunnel password 0 saba
!
!
!
username cisco password 0 cisco
interface FastEthernet0
description "Link to PPPoE Client"
no ip address
duplex auto
speed auto
pppoe enable group LAC-TEST
!
interface FastEthernet1
description Lik to MB
no ip address
duplex auto
speed 100
pppoe enable group LAC-TEST
*##Cisco 1811 (MPC8500) This client is PPPoE can connect PPPoE and it
is
working fine.*
interface FastEthernet0
description "Link to PPPoE Client'
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip virtual-reassembly
ip tcp adjust-mss 1452
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
no cdp enable
ppp authentication pap chap callin
ppp chap hostname cisco
ppp chap password 0 ciscopass
ppp pap sent-username cisco password 0 ciscopass
*##Cisco C887VA-W-A-K9( is the router that has problem with PPPoE
connected
to LNS)*
interface FastEthernet0
switchport access vlan 20
no ip address
pppoe-client dial-pool-number 1
!
!
interface Dialer1
description "Link to DSL CPE"
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname client1
ppp chap password 0 425198
ppp pap sent-username client1 password 0 425198
no cdp enable
Thanks in advance.
Dol
**
*Dol Meun, Network Operations - Level 1 - eintellego Pty Ltd*
[email protected] ; www.eintellego.asia
Cell +855 (0)15256904 ; skype://dolmeun
www.linkedin.com/in/dolmeun
#54, st. 350, Sangkat Boeung Keng Kang 3,
Chamkarmorn,Phnom Penh, Cambodia PO Box 710, Phnom Penh Cambodia
--
The Experts Who The Experts Call
Juniper - Cisco – Brocade - IBM
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
