Dear All, I have installed LNS with local authentication with the configuration below, I have two cisco router one is Cisco 1811 and I am using port fa0 connected to LNS fast0 then the PPPoE session is working fine. But for Cisco C887VA, I am using port Fast 0 on C887 connected to port Fast 1 on LNS but PPPoE is not working. is there any miss configure in my configuration or is there any restrict on Cisco C887 port for PPPoE connection. Note: on Cisco 1811 I use layer 3 port and Router Cisco 887 I use switchport as shown in the configuration. Is there anyone used to met this problem?
*##LNS (LAC and LNS in the same router)* aaa new-model ! ! aaa authentication login default local aaa authentication ppp default local ! ! aaa session-id common ! ! dot11 syslog ip source-route ! ! ! ! ip cef no ipv6 cef ! multilink bundle-name authenticated ! vpdn enable vpdn multihop vpdn aaa attribute nas-port vpdn-nas vpdn redirect vpdn logging vpdn logging local vpdn logging user vpdn logging tunnel-drop vpdn history failure table-size 50 vpdn session-limit 1400 vpdn search-order multihop-hostname domain dnis vpdn domain-delimiter @ suffix vpdn domain-delimiter / prefix ! vpdn-group LAC ! vpdn-group LAC-TEST request-dialin protocol l2tp domain eintellego.net domain direct.telstra.net initiate-to ip 192.168.55.2 source-ip 192.168.55.1 local name LAC l2tp tunnel password 0 saba ! ! ! username cisco password 0 cisco interface FastEthernet0 description "Link to PPPoE Client" no ip address duplex auto speed auto pppoe enable group LAC-TEST ! interface FastEthernet1 description Lik to MB no ip address duplex auto speed 100 pppoe enable group LAC-TEST *##Cisco 1811 (MPC8500) This client is PPPoE can connect PPPoE and it is working fine.* interface FastEthernet0 description "Link to PPPoE Client' no ip address no ip redirects no ip unreachables no ip proxy-arp ip virtual-reassembly ip tcp adjust-mss 1452 duplex auto speed auto pppoe enable group global pppoe-client dial-pool-number 1 ! interface Dialer1 ip address negotiated encapsulation ppp dialer pool 1 no cdp enable ppp authentication pap chap callin ppp chap hostname cisco ppp chap password 0 ciscopass ppp pap sent-username cisco password 0 ciscopass *##Cisco C887VA-W-A-K9( is the router that has problem with PPPoE connected to LNS)* interface FastEthernet0 switchport access vlan 20 no ip address pppoe-client dial-pool-number 1 ! ! interface Dialer1 description "Link to DSL CPE" ip address negotiated ip mtu 1452 ip nat outside ip virtual-reassembly in encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication chap pap callin ppp chap hostname client1 ppp chap password 0 425198 ppp pap sent-username client1 password 0 425198 no cdp enable Thanks in advance. Dol ** *Dol Meun, Network Operations - Level 1 - eintellego Pty Ltd* [email protected] ; www.eintellego.asia Cell +855 (0)15256904 ; skype://dolmeun www.linkedin.com/in/dolmeun #54, st. 350, Sangkat Boeung Keng Kang 3, Chamkarmorn,Phnom Penh, Cambodia PO Box 710, Phnom Penh Cambodia -- The Experts Who The Experts Call Juniper - Cisco – Brocade - IBM _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
