And what about Show inter ser 0/1/0
? Its probably down .... Ppp issues? Sent from a mobile device On 31/01/2013, at 9:52, false <[email protected]> wrote: > The T-1 seems to be up from a Layer-2 perspective. Something is wrong with my > routing though. The interface does NOT show up in the “sh ip route? Output. > I would expect to see it as a directly connected interface but it isn't > there. The card is in “slot 1” so I’m thinking that may have something to do > with but that’s just a hunch. We also have a 9-port switch in the router as > well. “Sh diag” looks clean too. Any ideas? > > router#sh ip route > Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP > D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area > N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 > E1 - OSPF external type 1, E2 - OSPF external type 2 > i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 > ia - IS-IS inter area, * - candidate default, U - per-user static route > o - ODR, P - periodic downloaded static route > > Gateway of last resort is x.x.92.1 to network 0.0.0.0 > > x.0.0.0/24 is subnetted, 1 subnets > C x.x.92.0 is directly connected, FastEthernet0/0 > S 192.168.10.0/24 [1/0] via 192.168.2.3 > 172.16.0.0/30 is subnetted, 1 subnets > C 172.16.31.48 is directly connected, Tunnel21 > 172.18.0.0/24 is subnetted, 2 subnets > S 172.18.3.0 [1/0] via 192.168.2.254 > S 172.18.1.0 [1/0] via 192.168.2.254 > S 192.168.1.0/24 [1/0] via 192.168.2.254 > C 192.168.2.0/24 is directly connected, Vlan10 > S 192.168.3.0/24 [1/0] via 192.168.2.254 > S* 0.0.0.0/0 [1/0] via x.x.92.1 > router# > > T-1 looks good here, plus no Alarms > > router#sh service-module serial 0/1/0 > Interface Serial0/1/0 > Module type is T1/fractional > Hardware revision is 1.0, Software revision is 001, > Image checksum is 0x0, Protocol revision is 0.1 > Receiver has no alarms. > Framing is ESF, Line Code is B8ZS, Current clock source is line, > Fraction has 24 timeslots (64 Kbits/sec each), Net bandwidth is 1536 > Kbits/sec. > Last module self-test (done at startup): Passed > Last clearing of alarm counters 00:17:16 > loss of signal : 0, > loss of frame : 0, > AIS alarm : 0, > Remote alarm : 0, > Module access errors : 0, > Total Data (last 0 15 minute intervals): > 0 Line Code Violations, 0 Path Code Violations > 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins > 1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs > Data in current interval (0 seconds elapsed): > 0 Line Code Violations, 0 Path Code Violations > 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins > 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs > router# > > > sh ver > System image file is "flash:c2801-adventerprisek9-mz.124-24.T.bin" > > > Cisco 2801 (revision 7.0) with 240640K/21504K bytes of memory. > Processor board ID FTX1046Z0J0 > 11 FastEthernet interfaces > 1 Serial interface > 1 terminal line > 1 Virtual Private Network (VPN) Module > 2 DSPs, 16 Voice resources > 1 cisco service engine(s) > DRAM configuration is 64 bits wide with parity disabled. > 191K bytes of NVRAM. > 62720K bytes of ATA CompactFlash (Read/Write) > > > interface Serial0/1/0 > ip address x.x.x.x 255.255.255.252 > encapsulation ppp > service-module t1 timeslots 1-24 > end > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
