Hello Mattias, but in the ME3600X (or ME3800X) is it possible to apply a configuration like this ?
interface gigabitethernet0/1.10100 no switchport encapsulation dot1q 10 second-dotq 100 ip address 10.0.0.1 255.255.255.0 with the ES+ (and I think also with 7600-SIP-400 + SPA-5X1GE-V2) is possible. Thanks, Davide 2013/2/28 Mattias Gyllenvarg <[email protected]>: > Do it in the 3600X, thats what there good at. > > > On 28 February 2013 09:55, Davide Ambrosi <[email protected]> > wrote: >> >> Thanks Mack, >> so I have to change all the 7603 boxes and move to 7603-S to support >> the ES+ cards and upgrade all the supervisors to SUP720-3B minimum. >> Moving to ASR's series (like the ASR1002) could be a good alternative >> choice because of the limited GE ports I need on the small POP's (5 >> GE) ? >> >> Davide >> >> >> 2013/2/27 Mack McBride <[email protected]>: >> > The ES+ cards are the way to go. >> > The OSM modules aren't going to do what you want. >> > In addition they aren't properly supported in newer code. >> > >> > LR Mack McBride >> > Network Architect >> > >> > -----Original Message----- >> > From: [email protected] >> > [mailto:[email protected]] On Behalf Of Davide Ambrosi >> > Sent: Wednesday, February 27, 2013 9:32 AM >> > To: [email protected] >> > Subject: [c-nsp] 802.1Q-in-Q VLAN Tag Termination on 7600/6500 OSN >> > modules >> > >> > Hello, >> > >> > We have some 7603 boxes with SUP720/SUP2 installed as main supervisor in >> > our MPLS Edge sites. >> > >> > Now we need to terminate QinQ VLAN directly on one or more GE interfaces >> > of the 7603 routers because we are planning to introduce metro ethernet >> > tecnologies (ME3400E/ME3600X) in our fiber and microwave access network for >> > reducing the VLAN configured between the switches located in the access >> > network (now we have 1 VLAN = 1 Customer). >> > >> > I see that 7600 catalyst modules doesn't support QinQ VLAN termination >> > (the command "encapsulation dot1q outer-vlan second-dot1q inner-vlan) >> > because they are "LAN" modules. >> > >> > Is there anyone who tested QinQ termination on old 7600 OSN GE modules >> > like the OSM-2+4GE-WAN+ ? If not supported the only way to support QinQ is >> > to buy new (expensive) 7600-S chassis + ES cards or SIP-400 and SPAs V2 ? >> > >> > In out network environment we have also some 7609-S(RSP720) with ES+ >> > card located into the core an large aggregation sites and with this >> > equipment we don't have problems because the QinQ Termination is supported >> > on ES+ card. >> > >> > >> > Davide >> > _______________________________________________ >> > cisco-nsp mailing list [email protected] >> > https://puck.nether.net/mailman/listinfo/cisco-nsp >> > archive at http://puck.nether.net/pipermail/cisco-nsp/ >> >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > -- > *Med Vänliga Hälsningar - Best Regards* > > *Mattias Gyllenvarg* > *Nätutveckling* > Bredband2 > > Tel: +46 406219712 > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
