IOS is 15.0.(1)M4 UCM is 8.0 I think you all are right about converting to H323
On Wed, Feb 3, 2016 at 12:54 PM, Brian Meade <[email protected]> wrote: > Some people claim it works okay with MGCP as long as you're on CUCM 8.x > and higher above a certain IOS version. It's definitely easier to just > switch to H.323 or SIP though. > > On Wed, Feb 3, 2016 at 12:49 PM, Ryan Huff <[email protected]> wrote: > >> You'll need to CFG the gateway as h.323 (at least for that FXO port). >> CLID doesn't work on FXO ports controlled by mgcpapp . You can run a "*debug >> vpm port x/x/x*" and that should show the calling name received on the >> FXO port, but if the port is under mgcpapp control, it won't pass the IE to >> CCM. >> >> >> Thanks, >> >> >> = Ryan = >> >> >> >> Email: [email protected] >> >> Spark: [email protected] >> >> Twitter: @ryanthomashuff <http://twitter.com/ryanthomashuff> >> >> LinkedIn: ryanthomashuff <http://linkedin.com/in/ryanthomashuff> >> >> Web ryanthomashuff.com >> >> >> ------------------------------ >> *From:* cisco-voip <[email protected]> on behalf of >> Brian Meade <[email protected]> >> *Sent:* Wednesday, February 3, 2016 12:38 PM >> *To:* David Zhars >> *Cc:* [email protected] >> *Subject:* Re: [cisco-voip] Caller ID issue >> >> What CUCM/IOS version? Do you have "Enable Caller ID" checked on the >> MGCP FXO device? You should have "caller-id enable" under the voice-port >> on the router. >> >> http://www.gossamer-threads.com/lists/cisco/voip/131620 >> >> On Wed, Feb 3, 2016 at 12:28 PM, David Zhars <[email protected]> wrote: >> >>> Sorry, just noticed in that example they reference ISDN. Again, calls >>> coming in on ISDN are fine, we get name and number. >>> It's when calls come in on the POTS lines that we just get the phone >>> number. >>> >>> On Wed, Feb 3, 2016 at 12:27 PM, David Zhars <[email protected]> wrote: >>> >>>> ISDN works fine. It's when the calls come in on the POTS line. >>>> >>>> I did find this by googling: >>>> >>>> interface serialx/x/x:23 >>>> isdn supp-service name calling >>>> >>>> I am not sure about the :23 after the serial port designation... >>>> >>>> >>>> On Wed, Feb 3, 2016 at 12:23 PM, Brian Meade <[email protected]> wrote: >>>> >>>>> Does the carrier send the caller name in the ISDN Setup message or in >>>>> a separate Facility message? Can you show "debug isdn q931" for one of >>>>> these inbound calls? >>>>> >>>>> On Wed, Feb 3, 2016 at 12:13 PM, David Zhars <[email protected]> wrote: >>>>> >>>>>> Cisco UCM 8.0 with 2801 in MGCP mode. >>>>>> Telco is sending Name and Number to us. >>>>>> Phones only ever display Number. >>>>>> >>>>>> In UCM, selected phones have both Caller Name and Caller Number >>>>>> ticked. >>>>>> >>>>>> Anything else could be preventing us from getting Names? >>>>>> >>>>>> _______________________________________________ >>>>>> cisco-voip mailing list >>>>>> [email protected] >>>>>> https://puck.nether.net/mailman/listinfo/cisco-voip >>>>>> >>>>>> >>>>> >>>> >>> >> >
_______________________________________________ cisco-voip mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-voip
