Cool. Thanks for the CiscoLive link…. I’ll take a look there after I do some more tutorials.
I did some experimenting to try and replicate what I saw on Github and think I understand the highlights a bit better now. The fact that you can have multiple macros makes me wonder, which takes precedence if two macros are “waiting” for the same thing. The other thing I can’t see is a way to manage things dynamically. It looks like you have to load things manually. If you update a macro, you have to reload it. On each device. Even if you have a hundred of them. I can appreciate that there might be APIs for me to use to go and push out update to each device, but it still requires me to maintain an inventory. I was hoping for the system to say “check for updates on these macros and load them in if there are changes” or something like that. OK. What I’m _really_ hoping for is that Control Hub to have templates to apply to devices. _That_ would be great. Lelio --- Lelio Fulgenzi, B.A. | Senior Analyst Computing and Communications Services | University of Guelph Room 037 Animal Science & Nutrition Bldg | 50 Stone Rd E | Guelph, ON | N1G 2W1 519-824-4120 Ext. 56354 | [email protected]<mailto:[email protected]> www.uoguelph.ca/ccs<http://www.uoguelph.ca/ccs> | @UofGCCS on Instagram, Twitter and Facebook [University of Guelph Cornerstone with Improve Life tagline] From: Anthony Holloway <[email protected]> Sent: Tuesday, October 8, 2019 2:47 PM To: Lelio Fulgenzi <[email protected]> Cc: voyp list, cisco-voip ([email protected]) <[email protected]> Subject: Re: [cisco-voip] Questions about in-room controls and macros I have never done this before, but according to: Integrated, Automated Meetings Rooms with CE xAPI and Macros - DEVNET-2071<https://www.ciscolive.com/c/dam/r/ciscolive/us/docs/2019/pdf/DEVNET-2071.pdf> Yes they run as soon as you enable them, and yes they can just do nothing until a certain triggering event occurs. Yes you can load multiple macros on a system. You can enable them individually too. Just be sure to save it first, else you wont be able to enable it. See below where I have two creatively named macros, doing amazing things, and one is enabled while the other is not. [cid:[email protected]] On Tue, Oct 8, 2019 at 11:44 AM Lelio Fulgenzi <[email protected]<mailto:[email protected]>> wrote: I'm going through the tutorials and unless I've missed something, like an introduction (which I'll look for again), I had a couple of questions... * Are macros always "running" ? It seems like this is the case... but a Macro can run and listen without doing anything until a certain action happens * Is there just one macro loaded per system or can you load multiple macros? The GUI seems a bit confusing Lelio --- Lelio Fulgenzi, B.A. | Senior Analyst Computing and Communications Services | University of Guelph Room 037 Animal Science & Nutrition Bldg | 50 Stone Rd E | Guelph, ON | N1G 2W1 519-824-4120 Ext. 56354 | [email protected]<mailto:[email protected]><mailto:[email protected]<mailto:[email protected]>> www.uoguelph.ca/ccs<http://www.uoguelph.ca/ccs><http://www.uoguelph.ca/ccs> | @UofGCCS on Instagram, Twitter and Facebook [University of Guelph Cornerstone with Improve Life tagline] _______________________________________________ cisco-voip mailing list [email protected]<mailto:[email protected]> https://puck.nether.net/mailman/listinfo/cisco-voip
_______________________________________________ cisco-voip mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-voip
