Hmm I didn't find that on the HW-SW matrix. As a matter a fact I couldn't
find PA-2FE-TX, only PA-2FEISL-TX and PA-FE-FX, both of which supported
12.1(3).
Robert
-----Original Message-----
From: David C Prall [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, May 30, 2001 9:04 AM
To: [EMAIL PROTECTED]
Subject: Re: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
Checkout the HW-SW Compatibility Table
http://www.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi
The PA-2FE-TX requires a minimum of 12.1(6) for Mainline.
David C Prall [EMAIL PROTECTED] http://dcp.dcptech.com
----- Original Message -----
From: "Robert Fowler"
To:
Sent: Wednesday, May 30, 2001 8:36 AM
Subject: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
> Hello,
>
> I've been beating my head on the side of this router. I've searched the
CCO
> on how to enable the PA-2FE adapter, and found some information on
> microcode. Then I found out the IOS I've upgraded to (12.1.(3)) already
has
> a current version built in. I don't recall learning anything about
Microcode
> in any of my studying. How does it differ from the IOS? Anyway, the
adapter
> card will not enable, and when I do a show diag 1 I get this:(see below)
> show that it is powered off. I've searched everywhere to find the command
to
> power it on. Any suggestions?
>
> Slot 1:
> Unknown (type 548) Port adapter
> Port adapter is disabled deactivated powered off
> Port adapter insertion time unknown
> EEPROM contents at hardware discovery:
> Hardware Revision : 1.0
> PCB Serial Number : MIC0516000Y
> Part Number : 73-5419-06
> Board Revision : A0
> RMA Test History : 00
> RMA Number : 0-0-0-0
> RMA History : 00
> Deviation Number : 0-0
> Model : PA-2FE-TX
> Part Number : 800-08350-06
> EEPROM format version 4
> EEPROM contents (hex):
> 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4D 49 43 30 35 31
> 0x10: 36 30 30 30 59 82 49 15 2B 06 42 41 30 03 00 81
> 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D
> 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20
> 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF
> 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
>
>
>
> Thank You,
> Robert Fowler
> Network Administrator
> MasTec, Inc.
> Office: 305.406.3150
> Fax: 305.599.7085
> Email: mailto:[EMAIL PROTECTED]
>
> MasTec Building the e-World
>
> Confidentiality Notice: The information contained in this transmittal,
> including any attachment, is privileged and confidential information and
is
> intended only for the person or entity to which it is addressed. If you
are
> neither the intended recipient nor the employee or agent responsible for
> delivering this message to the intended recipient, you are hereby notified
> that any disclosure, copying or distribution or the taking of any action
in
> reliance on the contents of this transmittal is strictly prohibited. If
you
> have received this transmittal in error, please contact the sender
> immediately and delete this transmittal from any computer or other data
> bank.
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=6441&t=6411
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
