I threw out that response because I saw for example that the pa-8e with a
rev below 1.14, altho fine on a 7206, is problematic on a vxr. I was not
sure which 7206 flavor was being discussed.
Brian "Sonic" Whalen
Success = Preparation + Opportunity
On Fri, 1 Jun 2001, Daniel Cotts wrote:
> The PA-2FE is supported in Cisco IOS Releases 12.1(5)E, 12.0(15)S, 12.1(6),
> 12.2(1), 12.2(2)T and after.
> HTH
>
> > -----Original Message-----
> > From: Brian [mailto:[EMAIL PROTECTED]]
> > Sent: Friday, June 01, 2001 8:57 PM
> > To: [EMAIL PROTECTED]
> > Subject: Re: FastEthernet Adapter for 7206 - How do I enable? [7:6411]
> >
> >
> > ancient hardware rev??
> >
> > Brian "Sonic" Whalen
> > Success = Preparation + Opportunity
> >
> >
> > On Wed, 30 May 2001, Robert Fowler wrote:
> >
> > > Hello,
> > >
> > > I've been beating my head on the side of this router. I've
> > searched the CCO
> > > on how to enable the PA-2FE adapter, and found some information on
> > > microcode. Then I found out the IOS I've upgraded to
> > (12.1.(3)) already has
> > > a current version built in. I don't recall learning anything about
> > Microcode
> > > in any of my studying. How does it differ from the IOS?
> > Anyway, the adapter
> > > card will not enable, and when I do a show diag 1 I get
> > this:(see below)
> > > show that it is powered off. I've searched everywhere to
> > find the command
> > to
> > > power it on. Any suggestions?
> > >
> > > Slot 1:
> > > Unknown (type 548) Port adapter
> > > Port adapter is disabled deactivated powered off
> > > Port adapter insertion time unknown
> > > EEPROM contents at hardware discovery:
> > > Hardware Revision : 1.0
> > > PCB Serial Number : MIC0516000Y
> > > Part Number : 73-5419-06
> > > Board Revision : A0
> > > RMA Test History : 00
> > > RMA Number : 0-0-0-0
> > > RMA History : 00
> > > Deviation Number : 0-0
> > > Model : PA-2FE-TX
> > > Part Number : 800-08350-06
> > > EEPROM format version 4
> > > EEPROM contents (hex):
> > > 0x00: 04 FF 40 02 24 41 01 00 C1 8B 4D 49 43 30 35 31
> > > 0x10: 36 30 30 30 59 82 49 15 2B 06 42 41 30 03 00 81
> > > 0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D
> > > 0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20
> > > 0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF
> > > 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> > > 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> > > 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
> > >
> > >
> > >
> > > Thank You,
> > > Robert Fowler
> > > Network Administrator
> > > MasTec, Inc.
> > > Office: 305.406.3150
> > > Fax: 305.599.7085
> > > Email: mailto:[EMAIL PROTECTED]
> > >
> > > MasTec Building the e-World
> > >
> > > Confidentiality Notice: The information contained in this
> > transmittal,
> > > including any attachment, is privileged and confidential
> > information and
> > is
> > > intended only for the person or entity to which it is
> > addressed. If you
> > are
> > > neither the intended recipient nor the employee or agent
> > responsible for
> > > delivering this message to the intended recipient, you are
> > hereby notified
> > > that any disclosure, copying or distribution or the taking
> > of any action in
> > > reliance on the contents of this transmittal is strictly
> > prohibited. If
> > you
> > > have received this transmittal in error, please contact the sender
> > > immediately and delete this transmittal from any computer
> > or other data
> > > bank.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=6949&t=6411
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
