Hello Friends - Its me again with TR problem. I tried each router
individually with different media filters. Still unsuccessful in getting
the int up. I ran through Cisco site with the error code - idb state. That
is what I found. Can someone tell me what kind of media filters, I should
use. I have a strong feeling it is the media filter causing the trouble.
Any thoughts would be appreciated.
Cisco site search feedback: On Error code idb state:
Error Message: %TR-3-BADSTART Unit [dec], Start completion and wrong idb
state -state= [dec] %TR-4-BKGND Unit [dec], bkgnd int: last packet out
[dec]ms %TR-4-BKGNDINT Unit [dec], bkgnd int: [hex][hex]
[hex][hex][hex][hex] [hex][hex] %TR-3-COMPFAIL Unit [dec], Tbuf completion
failure, result 0x[hex] %TR-3-FILTFAIL Unit [dec], SRB filter set failed:
0x[hex] 0x[hex]0x[hex] 0x[hex] (blk 0x[hex]) downing %TR-3-GETCONF Unit
[dec], get_config failed, result 0x[hex] 0x[hex]
Explanation:
The Token Ring interface contains firmware that is incompatible with the
system software.
Recommended Action:
Call Cisco Systems to upgrade the Token Ring Monitor firmware and/or the
system software.
I don't have maintenance contract with Cisco. It's my home lab that I am
trying to fix.
TIA / RamG
""RamG"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I have 2 routers {2502 & 2504}. Both TR are connected to ANDREW MAU 8228.
> I am unable to bring up the interface. I tried setting ring speed to 4 &
16
> but unsuccessful. I am using black box LT 056A Media Filters.
>
> I did check the archives. Mr. Vincent Chong faced similar problem on 29th
> March 2001 but there was no solution posted at the archive. This is what
I
> found - Problem fixed. Just follow Cisco recommendation and it works.
> Would appreciate, if he can share whatever info he was referring too. Msg
> being copied to VINCENT CHONG for help.
>
> What is meant by wrong idb state? I see this in debug event output
>
> Following is the interface & debug events output.
>
> 2504#show ip int brief
> Interface IP-Address OK? Method Status
> Protocol
> BRI0 unassigned YES NVRAM administratively
down
> down
> BRI0:1 unassigned YES unset administratively
down
> down
> BRI0:2 unassigned YES unset administratively
down
> down
> Serial0 192.1.1.2 YES NVRAM down
> down
> Serial1 193.1.1.2 YES NVRAM down
> down
> TokenRing0 unassigned YES NVRAM initializing
> down
>
> 00:43:02: TR0 starting.
> 00:43:23: TR0 receive SRB_FREE, state=2, if_state=6
> 00:43:24: %TR-3-OPENFAIL: Unit 0, open failed: Phys. Insertion, ring
> beaconing
> 00:43:24: %TR-3-BADSTART: Unit 0, Start completion and wrong idb state -
> state= 0
> 00:43:25: TR0: reset from 308F4F6
> 00:43:25: TR0: txtmr: 0x0, msclk: 0x27C15C, qt: 0x0 (2605400ms)
>
> Following is the condensed startup config output.
>
> R2504#show config
> Using 918 out of 32762 bytes
> !
> version 12.2
> no service single-slot-reload-enable
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname R2504
>
> interface TokenRing0
> no ip address
> ring-speed 4
>
> TX / RamG
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=8720&t=8554
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
