Would upgrading solve his problem? At 03:00 PM 5/9/02, Larry Letterman wrote: >I didn't say 10.3 would not handle it, did I...I just said to update the >ios because its old... > >Larry Letterman >Cisco Systems >[EMAIL PROTECTED] >----- Original Message ----- >From: "Priscilla Oppenheimer" >To: >Sent: Thursday, May 09, 2002 10:37 AM >Subject: Re: why I can't use normal ping in new router??? [7:43709] > > > > At 03:57 AM 5/9/02, Larry Letterman wrote: > > >Update the IOS to something modern... > > > > Do you work for TAC? Cisco IOS 10.3 could certainly handle ping just fine. > > ;-) > > > > I have a guess. Notice that the serial link has a subnet mask of > > 255.255.255.252. This is a subnet mask that you typically see on a > > point-to-point link with just two devices on it (the routers at either > > end). The link has no purpose other than to connect the customer's LAN to > > the ISP. Hence, there's no reason for the ISP to advertise a route to that > > point-to-point 100.20.90.56/30 network. In fact, for security reasons, >it's > > probably a good idea to make sure there is not a route to this dedicated > > network that has just two memebers, the two router interfaces. > > > > So, this means that there's no way for a ping reply to get back to the > > 100.20.90.58 address. > > > > Now, the LAN is addressed with a network number and subnet mask that you > > might see used for a typical small customer (60.80.200.113 > > 255.255.255.240). Undoubtedly, there are no problems getting back to this > > LAN. The fact that he can surf the Web proves that point. > > > > Priscilla > > > > > > > > > > >Larry Letterman > > >Cisco Systems > > >[EMAIL PROTECTED] > > >----- Original Message ----- > > >From: "Kenny Smith" > > >To: > > >Sent: Thursday, May 09, 2002 12:20 AM > > >Subject: RE: why I can't use normal ping in new router??? [7:43709] > > > > > > > > > > Below is my config...why you think there is a route missing somewhere, >as > > >I > > > > can still use extended ping to ping and I can use it to surf net as > > >normal. > > > > The only thing that I can't do is to normal ping from here.. What >should > > >me > > > > the problem? It is related to the new ISP? > > > > > > > > 2500new#sh conf > > > > Using 1561 out of 32762 bytes > > > > ! > > > > version 10.3 > > > > no service finger > > > > service password-encryption > > > > no service udp-small-servers > > > > no service tcp-small-servers > > > > ! > > > > hostname 2500new > > > > ! > > > > enable secret xxxxxx > > > > ! > > > > ip subnet-zero > > > > no ip source-route > > > > ! > > > > interface Ethernet0 > > > > description To Office Ethernet > > > > ip address 60.80.200.113 255.255.255.240 > > > > no ip directed-broadcast > > > > ip accounting output-packets > > > > ip route-cache same-interface > > > > ! > > > > interface Serial0 > > > > description XXX > > > > ip address 100.20.90.58 255.255.255.252 > > > > no ip directed-broadcast > > > > ip accounting output-packets > > > > bandwidth 512 > > > > ! > > > > interface Serial1 > > > > no ip address > > > > shutdown > > > > ! > > > > ip name-server 203.116.1.78 > > > > ip name-server 203.116.1.94 > > > > ip classless > > > > ip route 0.0.0.0 0.0.0.0 100.20.90.57 > > > > tftp-server flash \tftpboot\IGS-IN-L.BIN > > > > snmp-server community public RO > > > > banner exec ^C > > > > > > > > Router name: 2500new > > > > Platform: Cisco 2500 > > > > Location: Equant > > > > > > > > ^C > > > > banner login ^C > > > > > > > > Unauthorised access is prohibited and may lead to > > > > legal or disciplinary action being taken against you > > > > ^C > > > > ! > > > > line con 0 > > > > line aux 0 > > > > transport input all > > > > line vty 0 > > > > exec-timeout 15 0 > > > > password 7 XXXXXXXX > > > > login > > > > length 0 > > > > line vty 1 > > > > exec-timeout 0 0 > > > > password 7 XXXXXXX > > > > login > > > > line vty 2 4 > > > > password 7 XXXXXXX > > > > login > > > > ! > > > > end > > > > > > > > > > > > > > > > >From: Andrew Larkins > > > > >To: Kenny Smith , [EMAIL PROTECTED] > > > > >Subject: RE: why I can't use normal ping in new router??? [7:43709] > > > > >Date: Thu, 9 May 2002 08:53:34 +0200 > > > > > > > > > >my guess is that there is a route missing somewhere here from when >you > > > > >migrated to the new unit. Just to make sure, plse post the configs >and > > we > > > > >can see. > > > > > > > > > >-----Original Message----- > > > > >From: Kenny Smith [mailto:[EMAIL PROTECTED]] > > > > >Sent: 09 May 2002 07:54 > > > > >To: [EMAIL PROTECTED] > > > > >Subject: why I can't use normal ping in new router??? [7:43709] > > > > > > > > > > > > > > >May I know why I have to use extended ping/traceroute to ping from my > > new > > > > >router (2500new) and I have to specify extended command3yes, and >source > > > > >address is ethernet0 (serial0 don!&t work). If I just use ping > > > > >202.172.227.114. it doesn!&t works. Why??? And I can use !'ping > > > > >202.172.227.114!( to ping from my old router (2500old) !Vshown below. > > > > >Why??? Why I can only use extended ping and specify ethernet0. > > > > > > > > > >2500new#ping > > > > >Protocol [ip]: > > > > >Target IP address: 202.172.227.114 > > > > >Repeat count [5]: > > > > >Datagram size [100]: > > > > >Timeout in seconds [2]: > > > > >Extended commands [n]: y > > > > >Source address: ethernet0 > > > > >Type of service [0]: > > > > >Set DF bit in IP header? [no]: > > > > >Data pattern [0xABCD]: > > > > >Loose, Strict, Record, Timestamp, Verbose[none]: > > > > >Sweep range of sizes [n]: > > > > >Type escape sequence to abort. > > > > >Sending 5, 100-byte ICMP Echos to 202.172.227.114, timeout is 2 >seconds: > > > > >!!!!! > > > > >Success rate is 100 percent (5/5), round-trip min/avg/max = 16/22/40 >ms > > > > >2500new# > > > > >2500new#ping 202.172.227.114 > > > > >Type escape sequence to abort. > > > > >Sending 5, 100-byte ICMP Echos to 202.172.227.114, timeout is 2 >seconds: > > > > >..... > > > > >Success rate is 0 percent (0/5) > > > > >2500new# > > > > >2500new# > > > > > > > > > > > > > > >2500old#ping 202.172.227.114 > > > > > > > > > >Type escape sequence to abort. > > > > >Sending 5, 100-byte ICMP Echos to 202.172.227.114, timeout is 2 >seconds: > > > > >!!!!! > > > > >Success rate is 100 percent (5/5), round-trip min/avg/max = >44/171/376 > > ms > > > > > > > >2500old# > > > > > > > > > > > ________________________ > > > > Priscilla Oppenheimer > > http://www.priscilla.com ________________________
Priscilla Oppenheimer http://www.priscilla.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=43785&t=43709 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
