Hi, group.
I've been trying to get my ISDN working using Teltone ILS-2000. Here's my
config
and some basic show output. Please tell me what I'm missing. I tried doing
the
most
basic BRI config using HDLC as pointed out in Caslow, but even that did not
work.
Basically it seems to bring up the link for a few seconds and even bri 0 1
will show as
UP/UP but I am not getting any ping replies. Any help would be greatly
appreciated.
Elmer
2503#ping 172.16.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.1.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
2503#
04:00:33: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
04:00:53: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 2002 , call
lasted 20 seconds
04:00:53: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
2503#
isdn switch-type basic-ni
!
interface BRI0
ip address 172.16.1.1 255.255.255.0
dialer idle-timeout 90
dialer string 2002
dialer load-threshold 1 outbound
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866101 8358661
isdn spid2 0835866301 8358663
cdapi buffers regular 0
cdapi buffers raw 0
cdapi buffers large 0
!
ip kerberos source-interface any
ip classless
!
dialer-list 1 protocol ip permit
2503#sh isdn stat
Global ISDN Switchtype = basic-ni
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 74, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI = 75, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI 74, ces = 1, state = 5(init)
spid1 configured, spid1 sent, spid1 valid
Endpoint ID Info: epsf = 0, usid = 1, tid = 1
TEI 75, ces = 2, state = 5(init)
spid2 configured, spid2 sent, spid2 valid
Endpoint ID Info: epsf = 0, usid = 3, tid = 1
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
2503#sh dialer
BRI0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
2002 7 0 00:07:11 successful Default
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI0:1 - dialer type = ISDN
Idle timer (90 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI0:2 - dialer type = ISDN
Idle timer (90 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
2503#sh int bri0
BRI0 is up, line protocol is up (spoofing)
Hardware is BRI
Internet address is 172.16.1.1/24
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Last input 00:00:03, output 00:00:04, output hang never
Last clearing of "show interface" counters 00:27:32
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
138 packets input, 799 bytes, 0 no buffer
Received 5 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
155 packets output, 846 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
2516#
isdn switch-type basic-ni
!
interface BRI0
ip address 172.16.1.2 255.255.255.0
dialer idle-timeout 90
dialer string 2001
dialer load-threshold 1 outbound
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866201 8358662
isdn spid2 0835866401 8358664
cdapi buffers regular 0
cdapi buffers raw 0
cdapi buffers large 0
!
ip kerberos source-interface any
ip classless
!
dialer-list 1 protocol ip permit
2516#sh isdn stat
Global ISDN Switchtype = basic-ni
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 72, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI = 73, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI 72, ces = 1, state = 5(init)
spid1 configured, spid1 sent, spid1 valid
Endpoint ID Info: epsf = 0, usid = 2, tid = 1
TEI 73, ces = 2, state = 5(init)
spid2 configured, spid2 sent, spid2 valid
Endpoint ID Info: epsf = 0, usid = 4, tid = 1
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
2516#sh dialer
BRI0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
2001 8 0 00:00:07 successful Default
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI0:1 - dialer type = ISDN
Idle timer (90 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI0:2 - dialer type = ISDN
Idle timer (90 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Dial reason: Dialing on overload
Time until disconnect 80 secs
Current call connected 00:00:09
Connected to 2001
2516#sh int bri0
BRI0 is up, line protocol is up (spoofing)
Hardware is BRI
Internet address is 172.16.1.2/24
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Last input 00:00:01, output 00:00:01, output hang never
Last clearing of "show interface" counters 00:29:21
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
151 packets input, 914 bytes, 0 no buffer
Received 5 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
172 packets output, 964 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=45416&t=45416
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
