I am still looking for a Barient 18 self tailer or similar, if anyone knows of one.
Kevin On Tue, Sep 8, 2015, 6:02 PM Paul Baker via CnC-List <cnc-list@cnc-list.com> wrote: > I fitted them to my 24 and they worked fine, were a struggle to get on but > that meant they never slipped. > Cheers > Paul > > ------------------------------ > To: cnc-list@cnc-list.com > Date: Tue, 8 Sep 2015 17:08:15 -0300 > > Subject: Re: Stus-List Barient ST 32's > From: cnc-list@cnc-list.com > CC: rtaill...@eastlink.ca > > > I have them on my 25 and they work great. They came on a pair of Barient > 18s that I traded for another pair of winches I had and some splicing jobs. > > I don’t know what size they are but they almost look a size too small for > the winches, maybe that’s why I haven’t had the slippage problems that some > people have had. There is no way I could get my normal sheets in the outer > groove but my light air ones do fit. I use 5/16” sheets and the key is to > get three full wraps on the winch then grind it in to jam the top wrap > against the bottom of the Wincher, if I don’t do that the sheet will back > off. I like them because you can take in the majority of the sheet before > the load comes on then put on the third wrap and finish trimming in the > sail with one hand, great for single handed sailing. I still have to deal > with the sheet as it comes off the winch but I can crank it in a couple > turns before it gets around to the front of the winch, if you have someone > to tail this is a non-issue. > > > > > > Rick Taillieu > > Nemesis > > '75 C&C 25 #371 > > Shearwater Yacht Club > > Halifax, NS. > > > > > > > > *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Marek > Dziedzic via CnC-List > *Sent:* September-07-15 19:16 > *To:* C&C List > *Cc:* Marek Dziedzic > *Subject:* Re: Stus-List Barient ST 32's > > > > I had them on my C&C 24 and I could not make them to work. I removed them. > > > > But ymmv. > > > > Marek > > > > > > > > Sent from my Samsung device over Bell's LTE network. > > > > -------- Original message -------- > From: David Knecht via CnC-List <cnc-list@cnc-list.com> > Date: 2015-09-07 18:07 (GMT-05:00) > To: CnC CnC discussion list <cnc-list@cnc-list.com> > Cc: David Knecht <davidakne...@gmail.com> > Subject: Re: Stus-List Barient ST 32's > > What about $50 for Winchers ( > http://www.defender.com/product3.jsp?path=-1%7C118%7C2358547%7C2358555&id=899493 > <http://www.defender.com/product3.jsp?path=-1%7c118%7c2358547%7c2358555&id=899493>)? > I am considering trying one for one of my cabin top small secondaries. I > have read that they work. Dave > > > > Aries > > 1990 C&C 34+ > > New London, CT > > > > > On Sep 7, 2015, at 5:05 PM, Dennis C. via CnC-List <cnc-list@cnc-list.com> > wrote: > > > > Pairs of used self tailers on eBay go for $1000-1800 depending on size. > (There's a pair of 60 ST's out there now for $1700.) > > Winchmates are ~$550 each. That's $1100 a pair. > > Good used non-self tailers sell for $300-800 on eBay depending on size and > condition. > > I upgraded Touche's primary, secondary and cabin top winches from alloy to > chrome bronze. Net cost for 2 Barlow 28's, 2 Barlow 26's and 2 stainless > Barient 22's (all used non ST's) was around $600. Paid $1100 for the "new" > ones and sold two pairs of the old ones on eBay for $500 and tossed a pair > of 28's in the dumpster. > > > > Just saying.... > > Dennis C. > > > > On Mon, Sep 7, 2015 at 3:13 PM, Harry Hallgring via CnC-List < > cnc-list@cnc-list.com> wrote: > > Bill, > > Yes, that is probably what I will do for my primaries. > > Harry > > Sent from my iPad > > > On Sep 7, 2015, at 11:07 AM, Bill Coleman via CnC-List < > cnc-list@cnc-list.com> wrote: > > These? > > > > http://www.winchmate.com/store.html > > > > > > > > Bill Coleman > > C&C 39 > > > > > > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > ------------------------------ > > No virus found in this message. > Checked by AVG - www.avg.com > Version: 2015.0.6125 / Virus Database: 4419/10600 - Release Date: 09/08/15 > > _______________________________________________ Email address: > CnC-List@cnc-list.com To change your list preferences, including > unsubscribing -- go to the bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > >
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
