I have 2 panels with a goog amount of curve. When I put them up, I started
on the end with the least amount of bend putting screws every 8 inches. (reason
for brass screws). I did use 3ply veneer. I didn't pay attention to grain as I
was trying for maximum useage of each sheet of wood.
Doug MountjoysvPegasusLF38 just west of Ballard, WA.
------ Original message------From: sthoma20--- via CnC-List Date: Tue, Jan 26,
2016 07:18To: [email protected];Cc: [email protected];Subject:Re:
Stus-List 1980 C&C36 Headliner Panels
The panels over the galley and nav station on this boat would have a curve to
them. Were any of the panels on your 38 curved much? If so, how did you work
that out with 1/4" plywood? I was thinking that 1/8" would work ok, but that
1/4" might have to be steamed, or slotted on the back, or something like that.
Steve ThomasC&C36 MKIMerritt Island, FLC&C27 MKIIIPort Stanley, ON----
"[email protected] via CnC-List" wrote: > > I replaced my panels with
varnished African mahogany 1/4" plywood. Used brass screws to hold them up. >
Doug MountjoysvPegasusLF38 just west of Ballard, WA. > ------ Original
message------From: Dennis C. via CnC-ListDate: Mon, Jan 25, 2016 13:07To:
CnClist;Cc: Dennis C.;Subject:Re: Stus-List 1980 C&C36 Headliner Panels> I have
been trying to find that plastic at mcmaster.com for a couple years now.
Earlier today I emailed them for help. They sent me a link to a plastics
selector pack, () which contains several different samples of plastics. I'm
not excited about paying $57 for a sample pack which may or may not include
what I want.> > I still have some of the plastic. I think I may send a small
piece to mcmaster to see if they can match it.> > It's really good stuff and
has lots of uses on our boats. I've seen several posts which could be answered
with a link to this material.> > Dennis C.> Touche' 35-1 #83> Mandeville, LA> >
On Mon, Jan 25, 2016 at 1:48 PM, Dave Godwin via CnC-List wrote:> Steve,> Like
Dennis, I used some sort of plastic sheet (4’ x 8’ x ~1/8") the was similar,
white with a grain/rough surface on one side and completely smooth on the
other. I used the textured side and did like Wally Bryant on his LF 38 and used
SS oval screws with SS decorative washers to hold them up. Semi-industrial
look. It looks better because I spray-painted the interior white so the
matching is pretty close.> Best,> Dave Godwin> 1982 C&C 37 - Ronin> Reedville -
Chesapeake BayRonin’s Overdue Refit> On Jan 25, 2016, at 11:23 AM, Dennis C.
via CnC-List wrote:> Steve,> > I replaced the original old yellowed winch bolt
access panels on Touche' with plastic sheet from mcmaster.com. It was 1/8 or
so thick, smooth on one side and textured on the other. It looks very nice and
was easy to cut and finish. I countersunk the fastener holes for #6 or 8 flat
heads.> > I have tried several times over the years to find the invoice and
record the stock number. It's really nice stuff. > > Dennis C.> Touche' 35-1
#83> Mandeville, LA> > On Mon, Jan 25, 2016 at 7:22 AM, sthoma20--- via
CnC-List wrote:> The headliner panels for my new old boat are completely
missing, which is a bummer because the old ones would have been useful for
templates. It is what it is, but I don't even know what the originals looked
like, or what materials were used. I would appreciate any advice from owners of
similar boats, including whether or not there were options available.> > Steve
Thomas> C&C36 MKI> Merritt Island, FL> > C&C27 MKIII> Port Stanley, ON>
_______________________________________________Email
address:[email protected] change your list preferences, including
unsubscribing -- go to the bottom of page
at:http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
_______________________________________________
Email address:
[email protected]
To change your list preferences, including unsubscribing -- go to the bottom of
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
